A 58 Ni ion of charge 1 proton and mass 9.62x10-26kg is accelerated trough a potential difference of 3kV and deflected in a magnetic field of 0.12T. The velocity vector is perpendicular to the direction of magnetic field. a. [5] Find the radius of curvature of the ion's orbit. b. [4] A proton, accelerated to the same velocity as the 58Ni, also enters the same magnetic field. Is the radius of curvature of proton is going to be bigger/smaller/the same? Justify your answer.

Inductive reactance of the circuit= 53.66 Ohm

Capacitive reactance of the circuit= 12.24 Ohm

Impedance of the circuit = 98.89 Ohm

RMS current in the circuit = 1.32 A

Frequency to maximize the current = 105.43 Hz.

a) Inductive reactance of the circuit

Inductive reactance is given by the formula:

X(L) = 2πfL

Where,

f is the frequency

L is the inductance.Inductive reactance = 2πfL= 2 × 3.14 × 65 Hz × 130 mH= 53.66 Ohm (approx)

b) Capacitive reactance of the circuit

Capacitive reactance is given by the formula:

X(C) = 1/2πfC

Where, f is the frequency and C is the capacitance.

Capacitive reactance = 1/2πfC= 1/2 × 3.14 × 65 Hz × 200 µF= 12.24 Ohm (approx)

c) Impedance of the circuit

The impedance of the circuit is given by the formula:

Z = √(R² + (X(L) - X(C))²)

Where,

R is the resistance of the circuit,

X(L) is the inductive reactance,

X(C) is the capacitive reactance.

Impedance of the circuit = √(R² + (X(L) - X(C))²)= √(90² + (53.66 - 12.24)²)= 98.89 Ohm (approx)

d) RMS current in the circuit

RMS current in the circuit is given by the formula:

I(RMS) = V(RMS)/Z

Where,

V(RMS) is the RMS voltage of the alternating voltage source.

I(RMS) = V(RMS)/Z= 130 V / 98.89 Ohm= 1.32 A (approx)

e) Frequency to maximize the current in the circuit

To maximize the current in the circuit, we need to find the resonant frequency of the circuit. The resonant frequency of an RLC circuit is given by the formula:

f0 = 1/(2π√(LC))

Where,

L is the inductance

C is the capacitance.

f0 = 1/(2π√(LC))= 1/(2π√(130 mH × 200 µF))= 105.43 Hz (approx)

Therefore, the frequency that should be used to maximize the current in the circuit is approximately 105.43 Hz.

Learn more about  capacitive reactance.

https://brainly.com/question/14579743

#SPJ11

The minimum final speed of the bag of tools with respect to the space station that will keep the astronaut from drifting away forever is 20.34 m/s for the forces.

Question 1In the given problem, a man on a bicycle is pushed forward by a force of 1.050 × 10³ N. Air resistance pushes against him with a forces of 785 N. It is given that he starts from rest and is on a level road, and we are to find the speed v he will be going after 40.0 m. The mass of the bicyclist and his bicycle is 90.0 kg.Using Newton's Second Law, we can calculate the net force acting on the man:Net force = F - fwhere F = force pushing the man forwardf = force of air resistanceNet force =[tex](1.050 * 10^3)[/tex] - 785 = [tex]2.65 * 10^2 N[/tex]

Using Newton's Second Law again, we can calculate the acceleration of the man on the bicycle:a = Fnet / ma = (2.65 × [tex]10^2[/tex]) / 90 = 2.94 m/[tex]s^2[/tex]

Now, using one of the kinematic equations, we can find the speed of the man on the bicycle after 40.0 m:v² = v₀² + 2aswhere v₀ = 0 (initial speed) and s = 40 m (distance traveled)

[tex]v^2[/tex] = 0 + 2(2.94)(40) = 235.2v = [tex]\sqrt{232.5}[/tex]= 15.34 m/s

Therefore, the speed the man on the bicycle will be going after 40.0 m is 15.34 m/s.Question 2In the given problem, an astronaut is floating away from a space station, carrying only a rope and a bag of tools. The astronaut tries to throw the rope to his fellow astronaut but the rope is too short. In a last ditch effort, the astronaut throws his bag of tools in the direction of his motion, away from the space station. The astronaut has a mass of ma = 113 kg and the bag of tools has a mass of mb = 10.0 kg.

If the astronaut is moving away from the space station at vi = 1.80 m/s initially, we are to find the minimum final speed vb,f of the bag of tools with respect to the space station that will keep the astronaut from drifting away forever.Using the Law of Conservation of Momentum, we can write:mavi + mbvbi = mava + mbvbafter the astronaut throws the bag of tools, there is no external force acting on the system. Therefore, momentum is conserved. At the start, the momentum of the system is:ma × vi + mb × 0 = (ma + mb) × vafter the bag of tools is thrown, the astronaut and the bag will move in opposite directions with different speeds.

Let the speed of the bag be vb and the speed of the astronaut be va. The momentum of the system after the bag of tools is thrown is:ma × va + mb × vbNow, equating the two equations above, we get:ma × vi = (ma + mb) × va + mb × vbRearranging, we get:vb = (ma × vi - (ma + mb) × va) / mbSubstituting the given values, we get:vb = (113 × 1.80 - (113 + 10) × 0) / 10vb = 20.34 m/s

Therefore, the minimum final speed of the bag of tools with respect to the space station that will keep the astronaut from drifting away forever is 20.34 m/s.

Learn more about forces here:

https://brainly.com/question/13191643

#SPJ11

a.  The resistance of the wire is 1.909 ohms.

b. The current flowing through the wire is approximately 2.619 amperes.

a. The resistance of the wire can be calculated using the formula:

Resistance = (Resistivity * Length) / Area

In this case, the resistivity is given as 2, the length is 3m, and the radius is 1m. We can calculate the area of the wire using the formula for the area of a circle: Area = π * radius^2.

So, the area of the wire is π * 1^2 = π square meters. Substituting these values into the resistance formula:

Resistance = (2 * 3) / π = 6/π ≈ 1.909 ohms.

b. To calculate the current flowing through the wire, we can use Ohm's Law, which states that the current (I) is equal to the voltage (V) divided by the resistance (R):

Current = Voltage / Resistance.

Given that the voltage is 5 volts and the resistance is approximately 1.909 ohms (from part a), we can substitute these values into the formula:

Current = 5 / 1.909 ≈ 2.619 amperes.

Learn more about resistance of a wire:

https://brainly.com/question/13550678

#SPJ11

a)The average speed of the particle is 3 m/s.

b) The average acceleration of the particle is -1.5 m/s^2.

To determine the average speed and average acceleration of the particle, we need to calculate the displacement and change in velocity over the given time interval.

(a) Average speed is calculated by dividing the total distance traveled by the total time taken. In this case, we need to find the total displacement over the time interval.

Displacement = final position - initial position

Displacement = (-5 m) - (7 m)

Displacement = -12 m

Average speed = total displacement / total time

Average speed = (-12 m) / (7 s - 3 s)

Average speed = -12 m / 4 s

Average speed = -3 m/s

(b) Average acceleration is calculated by dividing the change in velocity by the total time taken.

Change in velocity = final velocity - initial velocity

Change in velocity = (-2 m/s) - (4 m/s)

Change in velocity = -6 m/s

Average acceleration = change in velocity / total time

Average acceleration = (-6 m/s) / (7 s - 3 s)

Average acceleration = -6 m/s / 4 s

Average acceleration = -1.5 m/s^2

To know more about acceleration

https://brainly.com/question/30660316

#SPJ11

The force constant of the spring is approximately 80.45 N/m, the spring will stretch approximately 0.1349 m (13.49 cm), the external agent must do approximately 1.739 J of work to stretch the spring, the elastic potential energy to be approximately 2.678 J and the speed of the block after leaving the spring to be approximately 0.618 m/s.

(a) The force constant of the spring can be calculated using Hooke's law, which states that the force exerted by a spring is directly proportional to its displacement. The formula for the force exerted by a spring is given by

[tex]F = k * x[/tex]

, where F is the force, k is the force constant (spring constant), and x is the displacement. Given that the spring stretches 2.66 cm (0.0266 m) when a 2.20 kg object is hung on it, we can rearrange the formula to solve for the force constant:

[tex]k = F / x = (m * g) / x = (2.20 kg * 9.8 m/s^2) / 0.0266 m[/tex]

(b) If the 2.20 kg object is removed and a 1.10 kg block is hung on the spring, we can use Hooke's law to find the spring's stretch. The force exerted by the spring is equal to the weight of the block:

[tex]F = m * g = 1.10 kg * 9.8 m/s^2[/tex]

Using the formula F = k * x and rearranging it to solve for x, we have:

[tex]x = F / k = (1.10 kg * 9.8 m/s^2) / 80.45 N/m[/tex]

(c) To find the work required to stretch the spring by 7.00 cm (0.07 m), we use the formula for work:

[tex]W = (1/2) * k * x^2[/tex]

Plugging in the values, we have:

[tex]W = (1/2) * 80.45 N/m * (0.07 m)^2[/tex]

(d) The elastic potential energy of the block-spring system can be calculated using the formula:

[tex]PE = (1/2) * k * x^2[/tex]

Plugging in the values, we have:

[tex]PE = (1/2) * 755 N/m * (0.0750 m)^2[/tex]

(e) After leaving the spring, the block's speed can be determined using the conservation of mechanical energy. Since the surface is frictionless, the initial potential energy stored in the spring is converted entirely into the kinetic energy of the block:

[tex]PE = KE(1/2) * k * x^2 = (1/2) * m * v^2[/tex]

Simplifying and solving for v, we have:

[tex]v = sqrt((k * x^2) / m)v = sqrt((755 N/m * 0.0750 m)^2 / 2.60 kg)[/tex]

To learn more about force constant

brainly.com/question/29598403

#SPJ11

Exoplanets are planets that orbit stars outside of our Solar System. Astronomers employ various methods to search for and study these distant planets.

Some of the key methods used are as follows:

1. Transit Method: Astronomers observe the apparent brightness of stars and look for periodic dips caused by planets passing in front of their host stars. When a planet transits, it blocks a portion of the star's light, resulting in a detectable decrease in the star's brightness. By analyzing the patterns of these brightness dips, scientists can infer the presence and characteristics of exoplanets.

2. Direct Imaging Method: This technique involves directly capturing images of exoplanets. Astronomers utilize advanced telescopes and instruments to detect the faint light emitted or reflected by planets. By observing the variability in apparent brightness or phase changes, similar to the phases of Venus and our moon, scientists gain insights into the properties of these exoplanets.

3. Transit Timing Variation Method: Astronomers study the precise timing of transit events to identify variations caused by the gravitational interactions between exoplanets in a multi-planet system. These variations manifest as slight deviations from the expected regularity in the timing of transits. By analyzing these variations, scientists can determine the presence and orbital parameters of additional exoplanets.

4. Radial Velocity Method: This approach involves analyzing the spectra of stars to identify subtle shifts in their spectral lines caused by the gravitational tug of orbiting exoplanets. As a planet orbits its star, it exerts a gravitational pull on the star, causing it to wobble slightly. This motion induces small changes in the star's spectral lines, which can be detected and used to infer the presence of exoplanets.

5. Astrometry Method: Astronomers measure the precise positions and motions of stars to detect any slight positional changes caused by the gravitational influence of orbiting exoplanets. By observing the apparent motion of stars due to the gravitational pull of unseen planets, scientists can infer the presence and characteristics of these exoplanets.

These diverse methods provide valuable insights into the existence, composition, orbital properties, and other characteristics of exoplanets. By combining multiple techniques, scientists continue to expand our understanding of the vast array of planets beyond our own Solar System.

Learn more about Astronomers

https://brainly.com/question/1764951

#SPJ11

A)For constructive interference of the reflected light, the 2nd minimum thickness of the Benzene layer is approximately 209.7 nm.

B)For destructive interference, the minimum thickness of the Benzene layer is approximately 139.8 nm.

For constructive interference of the reflected light, the path difference between the light reflected from the top surface of the Benzene layer and the light reflected from the Benzene-Glycerin interface should be equal to an integer multiple of the wavelength in the medium.

Mathematically, this can be expressed as:

[tex]\[ 2t_1 = m \lambda_1 \][/tex]

where [tex]\( t_1 \)[/tex] is the thickness of the Benzene layer,  m is an integer representing the order of interference, and [tex]\( \lambda_1 \)[/tex] is the wavelength of light in Benzene.

Given that the refractive index of Benzene is 1.501, we can calculate the wavelength of light in Benzene using the equation:

[tex]\[ \lambda_1 = \frac{\lambda_0}{n_1} \][/tex]

where [tex]\( \lambda_0 \)[/tex] is the wavelength of light in air and [tex]\( n_1 \)[/tex] is the refractive index of Benzene.

Substituting the given values, we find [tex]\( \lambda_1 = \frac{450}{1.501} \)[/tex] nm.

To find the 2nd minimum thickness, we consider \( m = 2 \). Rearranging the equation for constructive interference, we have:

[tex]\[ t_1 = \frac{m \lambda_1}{2} = \frac{2 \cdot \frac{450}{1.501}}{2} \) nm.[/tex]

Simplifying, we get [tex]\( t_1 \approx 209.7 \) nm.[/tex]

For destructive interference, the path difference should be equal to an odd multiple of half the wavelength. Using a similar approach, we can find that the minimum thickness is approximately 139.8 nm.

Therefore, the 2nd minimum thickness for constructive interference is 209.7 nm, and the minimum thickness for destructive interference is 139.8 nm.

Learn more about constructive interference here:

https://brainly.com/question/31228426

#SPJ11

(a) The length of the pendulum rod when the temperature drops to 0.0°C is: L' = L + ΔL= 1.6 m - 8.96 × 10⁻⁴ m= 1.5991 m≈ 1.599 m .(b)Therefore, the change in length of the rod causes the clock to run fast.

a. In order to find the length of the pendulum rod when the temperature drops to 0.0°C,

formula;`ΔL = L α ΔT`ΔL = change in length , L = initial lengthα = coefficient of linear expansionΔT = change in temperature

We can find the change in length as follows:ΔL = L α ΔT= 1.6 m × 18 × 10⁻⁶/°C × (-28)°C= -8.96 × 10⁻⁴ m

The minus sign indicates that the length has decreased.

Thus the length of the pendulum rod when the temperature drops to 0.0°C is: L' = L + ΔL= 1.6 m - 8.96 × 10⁻⁴ m= 1.5991 m≈ 1.599 m or 1599 mm (to four significant figures)

b. We know that the period of a pendulum is given by;T = 2π√ L/gWhere, L = Length of the pendulum g = Acceleration due to gravity π = 3.14T is directly proportional to the square root of L.

Hence, a decrease in length of the pendulum will cause the clock to run fast.

This is because, as the length decreases, the time period will also decrease which means the clock will tick faster.

Therefore, the change in length of the rod causes the clock to run fast.

Learn more about Acceleration due to gravity here:

https://brainly.com/question/13860566

#SPJ11

1) The approximately induced voltage per turn is (b) 11.

2) The iron loss at half-load will be (a) 125 W.

3) The transformer will have maximum efficiency at (c) 90% load.

4) The iron loss at 50 Hz is (c) 302 W.

5) The voltage per turn of the high voltage winding of a transformer is (c) less than the voltage per turn of the low voltage winding.

B) The low voltage winding is wound under the high voltage winding to ensure better insulation and protection. Placing the low voltage winding at the bottom reduces the risk of high voltage breakdown and improves safety.

1) The formula for calculating the induced voltage per turn in a transformer is given by V = 4.44 fΦBN, where:

- V is the induced voltage per turn

- f is the supply frequency (50 Hz in this case)

- Φ is the flux density (in Wb/m²)

- B is the area of the square core (in m²)

- N is the number of turns of the transformer

Given:

- f = 50 Hz

- Φ = 1 Wb/m²

- B = 24 cm = 0.24 m (assuming it is the side of the square core)

- Iron factor = 0.95

First, calculate the area of the square core:

B = (side of square)² = (0.24 m)² = 0.0576 m²

Next, calculate the induced voltage per turn using the formula:

V = 4.44 * 50 * 1 * 0.0576 = 12.2 V (approximately)

Since the iron factor is 0.95, the actual induced voltage per turn will be:

V' = 0.95 * V = 0.95 * 12.2 = 11.59 V (approximately)

Therefore, the approximately induced voltage per turn is 11.59 V.

2) The iron loss of a transformer is proportional to the square of the flux and hence it depends on the square of the applied voltage. Therefore, the iron loss at half-load will be less than the full-load. Let's calculate the iron loss at half load:

Given:

Iron loss at full load = 500 W

Let the iron loss at half load be P. Therefore:

Iron loss at half load / Iron loss at full load = (Voltage at half load / Voltage at full load)²

P / 500 = (0.5 / 1)²

P / 500 = 0.25

P = 0.25 * 500 = 125 W

Hence, the iron loss at half-load is 125 W.

3) The efficiency of a transformer is given by the ratio of output power to input power:

η = output power / input power

For a transformer, output power = V2I2 and input power = V1I1.

The efficiency can be written as:

η = V2I2 / V1I1 = (V2 / V1) * (I2 / I1)

Now, we know that the voltage regulation of a transformer is given by:

Voltage regulation = (V1 - V2) / V2 = (V1 / V2) - 1

So, V1 / V2 = 1 / (1 - voltage regulation)

It can be observed that when voltage regulation is zero, efficiency is maximum. Hence, a transformer will have maximum efficiency at full load.

Therefore, the maximum efficiency of a transformer is achieved at full load.

4) Hysteresis loss in a transformer is given by the formula:

Ph = ηBmax^1.6fVt

Where:

Ph is the hysteresis loss

η is the Steinmetz hysteresis coefficient (a function of the magnetic properties of the material)

Bmax is the maximum flux density

f is the supply frequency

Vt is the volume of the core

In this case, we are given the iron loss at 50 Hz, which is equal to 500 W. Let's calculate the hysteresis loss at 50 Hz:

Given:

Iron loss at

50 Hz = P = 500 W

Since the flux density is the same, the hysteresis loss and eddy current loss are independent of frequency.

Therefore, the total iron loss at 50 Hz is the sum of hysteresis loss and eddy current loss:

Total iron loss at 50 Hz = hysteresis loss + eddy current loss = 500 W

Hence, the total iron loss at 50 Hz is 500 W.

5) The voltage per turn of a transformer is given by V / N, where V is the voltage and N is the number of turns. The voltage ratio of a transformer is given by the ratio of the number of turns of the high voltage winding to the number of turns of the low voltage winding.

Since the voltage ratio is defined as the high voltage divided by the low voltage, the voltage per turn of the high voltage winding is greater than the voltage per turn of the low voltage winding.

Therefore, the voltage per turn of the high voltage winding is greater than the voltage per turn of the low voltage winding.

To know more about transformer click here:

https://brainly.com/question/15200241

#SPJ11

The complete question is:

1-ph transformer, 50Hz, core type transformer has square core of 24 cm side. The flux density is 1 Wb/m². If the iron factor is 0.95, the approximately induced voltage per turn is a) 6 b) 11 12 d) none of the above. 2-A transformer has full-load iron loss of 500 W. the iron loss at half-load will be a) 125 W b) 250 W 500 W d) none of the above. 3-A transformer will have maximum efficiency at ----------. a) full-load b) no-load c) 90% load none of the above 4-The hysteresis loss in a certain transformer is 40W and the eddy current loss is 50 W (both at 30Hz), then the iron loss at 50 Hz is ----. The flux density being the same. a) 180W 204W c) 302 none of the previous d)500W. 5-The voltage per turn of the high voltage winding of a transformer is per turn of the low voltage winding. the voltage a) More than b) the same as c) less than d) none of the previous e) the low voltage winding. B- 1- The low voltage winding is wound under the high voltage

Given that, A solar cell has a light-gathering area of 10 cm2 and produces 0.2 A at 0.8 V (DC) when illuminated with S = 1 000 W/m2 sunlight. We need to determine the efficiency of the solar cell. The option (A) 16.7% is the correct answer.

To calculate the efficiency of the solar cell, we need to use the formula given below:

Efficiency = (Power output / Power input) × 100%

where,

Power output = I × V (DC)

and

Power input = S × A

where, S = 1000 W/m² (irradiance)A = 10 cm² = 0.001 m²

I = 0.2 AV (DC) = 0.8 V

Now, we have all the given data, we can put the values in the formula.

Efficiency = (Power output / Power input) × 100%

Efficiency = [0.2 A × 0.8 V / (1000 W/m² × 0.001 m²)] × 100%

Efficiency = 16.0% ≈ 16.7%

Therefore, the efficiency of the solar cell is 16.7%.

To learn more about solar cell, refer:-

https://brainly.com/question/29553595

#SPJ11

For the volume of 670 liters and the time of 6.0 minutes, the speed of the water in the hose is approximately 0.043 meters per second.

The speed of water in the hose can be calculated by dividing the volume of water that flows through the hose by the time it takes to fill the tub.

Given that the volume is 670 liters and the time is 6.0 minutes, we can determine the speed of the water in meters per second.

To find the speed of the water in the hose, we need to convert the given volume and time into consistent units.

First, let's convert the volume from liters to cubic meters.

Since 1 liter is equal to 0.001 cubic meters, we have:

V = 670 liters = 670 * 0.001 cubic meters = 0.67 cubic meters

Next, let's convert the time from minutes to seconds.

Since 1 minute is equal to 60 seconds, we have:

Δt = 6.0 minutes = 6.0 * 60 seconds = 360 seconds

Now, we can calculate the speed of the water using the formula:

Speed = Volume / Time

Speed = 0.67 cubic meters / 360 seconds ≈ 0.00186 cubic meters per second

Since the speed is given in cubic meters per second, we can convert it to meters per second by taking the square root of the speed:

Speed = √(0.00186) ≈ 0.043 meters per second

Therefore, the speed of the water in the hose is approximately 0.043 meters per second.

Learn more about speed here:

https://brainly.com/question/13943409

#SPJ11

(a) The speed of the bead at point A is 6.47 m/s.

(b) The normal force on the bead at point A is 2.49 N

(c) The minimum height h from which the bead can be released is 5R/2.

(a)

Use the conservation of energy principle.

The initial energy, when the bead is released from rest at a height h = 3.60R, is entirely due to its potential energy.

The final energy of the bead at point A is entirely due to its kinetic energy, since it is sliding without friction around the loop-the-loop.

Let M be the mass of the bead and v be its velocity at point A, then we have:

Mgh = 1/2MV² + MgR

where g is the acceleration due to gravity, and h = 3.60R is the height from which the bead is released.

Simplifying and solving for v gives:

v = sqrt(2gh - 2gR)

where sqrt() stands for square root.

Substituting the values of g and R gives:

v = sqrt(2*9.81*3.6 - 2*9.81*1)

v = 6.47 m/s

Therefore, the speed of the bead at point A is 6.47 m/s.

(b)

To find the normal force on the bead at point A, we need to consider the forces acting on the bead at this point.

The normal force is the force exerted by the wire on the bead perpendicular to the wire. It balances the force of gravity on the bead.

At point A, the forces acting on the bead are the force of gravity acting downwards and the normal force acting upwards.

Since the bead is moving in a circular path, it is accelerating towards the center of the loop.

Therefore, there must be a net force acting on it towards the center of the loop.

This net force is provided by the component of the normal force in the direction towards the center of the loop.

This component is given by:

Ncosθ = MV²/R

where θ is the angle between the wire and the vertical, and N is the normal force.

Substituting the values of M, V, and R gives:

Ncosθ = 5.50*10⁻³*(6.47)²/1

Ncosθ = 2.49

Therefore, the normal force on the bead at point A is 2.49 N.

(c)

The bead will lose contact with the wire at the top of the loop when the normal force becomes zero.

This occurs when the component of the force of gravity acting along the wire becomes equal to the centripetal force required to keep the bead moving in a circular path.

The component of the force of gravity along the wire is given by:

Mg sinθ = MV²/R

where θ is the angle between the wire and the vertical, and Mg is the force of gravity acting downwards.

Substituting the values of M, V, and R gives:

Mg sinθ = 5.50*10⁻³*(6.47)²/1

Mg sinθ = 0.789

Since sinθ can never be greater than 1, we have:

Mg sinθ ≤ Mg

The minimum height h from which the bead can be released is obtained by equating the potential energy of the bead at this height to the kinetic energy required to keep the bead moving in a circular path at the top of the loop.

This gives:

Mgh = 1/2MV² + MgR

Substituting V² = gR and simplifying gives:

h = 5R/2

Therefore, the minimum height h from which the bead can be released is 5R/2.

Learn more about the normal force:

brainly.com/question/29458258

#SPJ11

therefore, the correct option is 3A.Note:In a parallel combination of resistors, the voltage drop across each resistor will be the same. But the current through each resistor is different and is calculated using Ohm's law.

The circuit is given as below: Circuit diagram of resistorsThe total resistance of the circuit is calculated as:Rt = 4 Ω + 6 Ω + 12 Ω + 5 ΩRt = 27 ΩThe current across the circuit is calculated using Ohm's law as:

V = IR27 V = I × 27 ΩI = 27 / 9I = 3 ATake a loop across 5 Ω resistor and write KVL equation as:V = IR5V = I × 5 ΩV = 3 × 5V = 15 VTherefore, the current through 5.0 Ω resistor is I = V / R = 15 / 5 = 3 A.As,

the current through 5.0Ω resistor is 3A; therefore, the correct option is 3A.Note:In a parallel combination of resistors, the voltage drop across each resistor will be the same.

But the current through each resistor is different and is calculated using Ohm's law.

to know more about Ohm's law

https://brainly.com/question/1476670

#SPJ11

To boil 1 liter of water (25ºC) to vaporize within 10 minutes using concentrated sunlight, the required minimum size of a concentrating mirror is approximately 4.3 square meters.

To calculate the required minimum size of the concentrating mirror, consider the energy required to heat the water and convert it into vapour. The specific heat of water is 4.19 kJ/kg.K, which means it takes 4.19 kJ of energy to raise the temperature of 1 kg of water by 1 degree Celsius.

The latent heat of water is 2264.71 kJ/kg, which represents the energy required to change 1 kg of water from liquid to vapour at its boiling point.

First, determine the mass of 1 litre of water. Since the density of water is 1 kg/litre, the mass will be 1 kg. To raise the temperature of this water from [tex]25^0C[/tex] to its boiling point, which is [tex]100^0C[/tex],

calculate the energy required using the specific heat formula:

Energy = mass × specific heat × temperature difference

[tex]1 kg * 4.19 kJ/kg.K * (100^0C - 25^0C)\\= 1 kg * 4.19 kJ/kg.K * 75^0C\\= 313.875 kJ[/tex]

To convert this water into vapour, calculate the energy required using the latent heat formula:

Energy = mass × latent heat

= 1 kg × 2264.71 kJ/kg

= 2264.71 kJ

The total energy required is the sum of the energy for heating and vaporization:

Total energy = 313.875 kJ + 2264.71 kJ

= 2578.585 kJ

Now, determine the time available to supply this energy. 10 minutes, which is equal to 600 seconds. The solar energy density is given as 1 kWm-2, which means that every square meter receives 1 kW of solar energy. Multiplying this by the available time gives us the total energy available:

Total available energy = solar energy density * time

= [tex]1 kW/m^2 * 600 s[/tex]

= 600 kWs

= 600 kJ

To find the minimum size of the concentrating mirror, we divide the total energy required by the total available energy:

Minimum mirror size = total energy required / total available energy

= 2578.585 kJ / 600 kJ

= [tex]4.3 m^2[/tex]

Therefore, approximately 4.3 square meters for the concentrating mirror is required.

Learn more about concentrating mirror here:

https://brainly.com/question/31588513

#SPJ11

To prove the effective thickness equation, we need to start with the basic equation for thermal resistance in a composite wall. The thermal resistance of a composite wall can be expressed as:

1/[tex]R_{total[/tex] = Σ[tex](L_i / k_i)[/tex],

where [tex]R_{total[/tex] is the total thermal resistance, [tex]L_i[/tex] is the thickness of each layer i, and [tex]k_i[/tex] is the thermal conductivity of each layer i.

Now, let's consider a composite wall consisting of multiple layers with varying thicknesses. The effective thickness ([tex]L_{eff[/tex]) is defined as the thickness of a single imaginary layer that would have the same thermal resistance as the composite wall. We want to derive an equation for [tex]L_{eff[/tex].

To begin, we can rewrite the thermal resistance equation for the composite wall as:

1/[tex]R_{total[/tex] = ([tex]L_1 / k_1) + (L_2 / k_2) + ... + (L_n / k_n)[/tex],

where n is the total number of layers in the composite wall.

Now, we introduce the concept of effective thermal conductivity ([tex]k_{eff)[/tex], which is the thermal conductivity that the composite wall would have if it were replaced by a single imaginary layer with thickness [tex]L_{eff[/tex]. We can express this as:

[tex]k_{eff[/tex] = Σ[tex](L_i / k_i[/tex]).

The effective thermal conductivity represents the ratio of the total thickness of the composite wall to the total thermal resistance.

Next, we can rearrange the equation for the effective thermal conductivity to solve for[tex]L_{eff[/tex]:

[tex]k_{eff = L_{eff / R_{total.[/tex]

Now, we can substitute the expression for the total thermal resistance ([tex]R_{total[/tex]) from the thermal resistance equation:

[tex]k_{eff = L_{eff / ((L_1 / k_1) + (L_2 / k_2) + ... + (L_n / k_n)[/tex]).

Finally, by rearranging the equation, we can solve for [tex]L_{eff[/tex]:

[tex]L_eff = k_eff / ((1 / L_1) + (1 / L_2) + ... + (1 / L_n)).[/tex]

This is the effective thickness equation, which gives the thickness of a single imaginary layer that would have the same thermal resistance as the composite wall.

The effective thickness equation allows us to simplify the analysis of composite walls by replacing them with a single equivalent layer. This concept is particularly useful when dealing with heat transfer calculations in complex systems with multiple layers and varying thicknesses, as it simplifies the calculations and reduces the system to an equivalent homogeneous layer.

Learn more about resistance here:

https://brainly.com/question/14547003

#SPJ11

Answer:

The correct option is:

O add the numbers from the three sliders to determine the mass of an object

The ratio of the temperature of the first star to the temperature of the second star is 4:1

In order to calculate the ratio of the temperature of the first star to the temperature of the second star, we need to use the Stefan-Boltzmann law.

What is the Stefan-Boltzmann law?

The Stefan-Boltzmann law states that the rate of radiation emitted by a black body is proportional to the fourth power of the body's absolute temperature.

What is the formula of Stefan-Boltzmann law?

The formula for Stefan-Boltzmann law is given as:

q = εσT^4

Where,

q = the energy radiated per unit area per unit time.

ε = Emissivity (In this case, it's 1).

σ = Stefan-Boltzmann constant = 5.67 × 10-8 W/m2.K4.

T = Temperature in Kelvin.

Now, let's proceed to solve the problem.

Given,

Emissivity of both stars (ε) = 1

Radius of the first star (r1) = 2r2 (i.e twice as large as the second star)

According to Stefan-Boltzmann law,

q1/q2 = (T1^4/T2^4)

We know that

q1 = q2 , because both the stars radiate thermal energy at the identical rate.

q1/q2 = 1

q1 = εσT1^4A1

q2 = εσT2^4A2

As the area of both stars is not given, we can assume it as same for both the stars.

q1 = q2εσT1^4

A = εσT2^4A

q1/q2

= T1^4/T2^4

= (r1/r2)^2q1/q2

= (r1/r2)^2

= (2r2/r2)^2

= 2^2

= 4

Therefore,

The ratio of the temperature of the first star to the temperature of the second star is 4:1

Answer: 4:1

Learn more about Stefan-Boltzmann law here

https://brainly.com/question/30763196

#SPJ11

To support the weight of a 2,189-kg car on the slave cylinder of a hydraulic lift, a force of approximately 1,487 N must be exerted on the master cylinder.

The hydraulic lift operates based on Pascal's principle, which states that pressure applied to an enclosed fluid is transmitted undiminished to all parts of the fluid and the walls of the container. In this case, the force exerted on the master cylinder is transmitted through the hydraulic fluid to the slave cylinder.

First, we need to calculate the area of each cylinder. The area of a circle is given by the formula A = πr^2, where r is the radius. The diameter of the master cylinder is 1.7 cm, so the radius is half of that, which is 0.85 cm or 0.0085 m. Thus, the area of the master cylinder is A_master = π(0.0085 m)^2.

Similarly, the diameter of the slave cylinder is 25 cm, so the radius is 12.5 cm or 0.125 m. The area of the slave cylinder is A_slave = π(0.125 m)^2.

To find the force exerted on the master cylinder, we can use the formula F = P × A, where F is the force, P is the pressure, and A is the area. Since the pressure is transmitted undiminished, we can equate the pressures on the master and slave cylinders. Therefore, P_master × A_master = P_slave × A_slave.

Rearranging the equation, we get P_master = (P_slave × A_slave) / A_master. The weight of the car is given by the formula W = m × g, where m is the mass and g is the acceleration due to gravity (approximately 9.8 m/s^2).

Substituting the values, we have W = 2,189 kg × 9.8 m/s^2.

Now, we can solve for P_slave using the equation P_slave = W / A_slave. Plugging in the known values, we calculate P_slave.

Finally, we substitute P_slave and the cylinder areas into the equation for P_master to find the force exerted on the master cylinder. The result is approximately 1,487 N.

Learn more about Pascal's principle:

https://brainly.com/question/30258629

#SPJ11

The solution to the problem is as follows:Part AIt is given that, the resistance of the circuit abcd is 3.00 Ω.Now, the potential difference across ab = v(ab) = IR = 3.00 Ω * 3.00 A = 9.00 V (by ohm's law)The potential difference across bc = v(bc) = IR = 3.00 Ω * 3.00 A = 9.00 V (by ohm's law)Hence, v(ab) = v(bc) = 9.00 VPart BIt is given that, the current I in the wire cd is 11 A.  

Let's consider a small segment of wire with length x at a distance of y from wire ab.We know that the force per unit length between two parallel wires carrying current is given by f/L = (μ₀ * I * I') / (2πd),Where,μ₀ = Permeability of free spaceI, I' = Currents in the two wiresd = Distance between the two wires.Now, the total force on the small segment = f = (μ₀ * I * I' * x) / (2πy)Hence, the total force on the wire cd due to wire ab = f(ab) = ∫(μ₀ * I * I' * x) / (2πy) dx (from x=0 to x=6.00 cm) = (μ₀ * I * I' * ln(2)) / (πy) ... (1)Similarly, the total force on the wire cd due to wire ef = f(ef) = (μ₀ * I * I' * ln(4)) / (πy) ... (2)Now, the total force on the wire cd is given by,F = sqrt(f(ab)² + f(ef)²) ... (3)F = sqrt(μ₀² * I² * I'² * (ln(2))² + μ₀² * I² * I'² * (ln(4))²) / π² ... (4)F = (μ₀ * I * I') / π * sqrt(ln(2)² + ln(4)²) ... (5)F = (μ₀ * I * I') / π * sqrt(5) ... (6)F = (4π * 10⁻⁷ T m/A * 3.00 A * 11 A) / (π * sqrt(5)) = 2.65 * 10⁻⁵ N ... (7)Therefore, the force on wire cd is directed to the left and its magnitude is 2.65 x 10⁻⁵ N.Part CThe direction of the force required to keep the rod moving to the right with a constant speed of 9.00 m/s is no force is needed.Part DThe magnitude of the force mentioned in Part C is zero. Hence, the answer is 0 N.

Learn more on speed here:

brainly.in/question/47776531

#SPJ11

A simple series circuit consists of a 190 Ω resistor, a 28.0 V battery, a switch, and a 1.70 pF parallel-plate capacitor  the displacement current at t = 0.50 ns will be zero since there is no change in electric flux through the capacitor plates.

To find the displacement current at t = 0.50 ns in the given circuit, we need to determine the rate of change of electric flux through the capacitor plates.

The displacement current (Id) can be calculated using the formula: Id = ε₀ × (dΦE / dt), where ε₀ is the permittivity of free space, dΦE/dt is the rate of change of electric flux through the capacitor.

In this case, the capacitor is initially uncharged, so there is no electric field (E) between the plates. Therefore, the electric flux through the capacitor is initially zero, and its rate of change is also zero.

Since the switch is closed at t = 0s, it will take some time for the capacitor to charge up and establish an electric field between its plates. At t = 0.50 ns, the capacitor is still in the process of charging, and the electric field has not fully developed.

As a result, the displacement current at t = 0.50 ns will be zero since there is no change in electric flux through the capacitor plates. Once the capacitor is fully charged and the electric field is established, the displacement current will start to flow, but at t = 0.50 ns, it is still not present.

Learn more about capacitor here:

https://brainly.com/question/31627158

#SPJ11

2.1. The potential energy of the water at the top of the falls with respect to the base of the falls is 981 J.2.2 The kinetic energy of the water just before it strikes bottom is 981 J.2.3The state of the water changes from kinetic energy to internal energy.

2.1 Potential energy of the water at the top of the falls with respect to the base of the fallsThe potential energy of the water at the top of the falls with respect to the base of the falls is given byPE = mghWhere,m = 1 kg, g = 9.81 m/s², h = 100 mPutting the given values in the above formula we get,PE = 1 × 9.81 × 100 = 981 J.

Therefore, the potential energy of the water at the top of the falls with respect to the base of the falls is 981 J.

2.2 Kinetic energy of the water just before it strikes bottomThe kinetic energy of the water just before it strikes bottom is given byKE = 1/2 mv²Where,m = 1 kg, v = ?KE = 981 J (the potential energy of the water).

As per the law of conservation of energy, the potential energy of water at the top of the falls gets converted into kinetic energy just before it strikes the bottom.Therefore, KE = PEAs we know,KE = 1/2 mv²Therefore,1/2 mv² = 981On solving the above equation we get,v² = 1962v = √1962 = 44.28 m/sTherefore, the kinetic energy of the water just before it strikes bottom is 981 J.

2.3 After the 1 kg of water enters the stream below the falls, what change has occurred in its state?After the 1 kg of water enters the stream below the falls, the kinetic energy of the water gets converted into internal energy. This is due to the collisions of water molecules in the stream.

The internal energy in water molecules increases due to the collisions, and the temperature of the water also increases. Therefore, the state of the water changes from kinetic energy to internal energy.

Learn more about Kinetic energy here,

https://brainly.com/question/8101588

#SPJ11

The sound intensity level that delivers 4.4 p) of energy to the eardrum each second with a 7.5 mm diameter is 40 dB.

Sound intensity level is measured in decibels (dB) and is a logarithmic scale used to quantify the loudness of a sound. The formula to calculate sound intensity level in decibels is given by:

[tex]L = 10 * log10(I/I_0)[/tex]

Where L is the sound intensity level, I is the sound intensity, and I₀ is the reference intensity (usually taken as the threshold of hearing, which is [tex]10^{(-12)}[/tex]watts per square meter).

To solve this problem, we need to find the sound intensity level when 4.4 p) (which stands for [tex]4.4 * 10^{(-12)}[/tex]) of energy is delivered to the eardrum each second. We can substitute the values into the formula:

[tex]40 = 10 * log10(4.4 * 10^{(-12)}/I_0)[/tex]

Simplifying the equation, we get:

[tex]log10(4.4 * 10^{(-12)}/I_0) = 4[/tex]

Taking the antilogarithm of both sides, we find:

[tex]4.4 * 10^{(-12)}/I_0= 10^4[/tex]

Solving for [tex]I_o[/tex], we get:

[tex]I_0= 4.4 * 10^{(-12)}/10^4 = 4.4 * 10^{(-16)}[/tex]

Therefore, the sound intensity level that delivers 4.4 p) of energy to the eardrum each second is 40 dB.

Learn more about Sound intensity here:

https://brainly.com/question/32194259

#SPJ11

In the context of LTE-A (Long-Term Evolution Advanced), Type 1 and Type 1a relay nodes are different deployment options for relay nodes in the LTE network. Relay nodes are used to extend the coverage and improve the performance of the network by relaying signals between the base station and user equipment (UE).

Type 1 Relay Node:

A Type 1 relay node in LTE-A operates in half-duplex mode, which means it can either transmit or receive data at a given time but not both simultaneously. It has two separate sets of antennas: one for receiving signals from the base station (downlink) and another for transmitting signals to the UE (uplink). This type of relay node introduces a relay-specific interface called the Relay Physical Interface (R-PHY) to connect with the base station.

The Type 1 relay node receives downlink signals from the base station, decodes them, and then re-encodes and retransmits them to the UE. Conversely, it receives uplink signals from the UE, decodes them, and re-encodes and retransmits them to the base station. Due to the half-duplex operation, it cannot receive and transmit simultaneously, which can result in increased latency and reduced throughput compared to other relay types.

Type 1a Relay Node:

A Type 1a relay node is an enhanced version of the Type 1 relay node, specifically designed to improve performance. It operates in full-duplex mode, allowing simultaneous transmission and reception. It achieves this by utilizing advanced self-interference cancellation techniques, which cancel out the interference caused by the transmitted signal, allowing the relay to receive signals while transmitting.

The Type 1a relay node also utilizes the Relay Physical Interface (R-PHY) to communicate with the base station. By supporting full-duplex operation, it can provide better throughput and lower latency compared to the Type 1 relay node. This makes it more suitable for scenarios where higher data rates and improved performance are desired.

Both Type 1 and Type 1a relay nodes can be deployed in LTE-A networks to extend coverage and improve performance in areas with challenging propagation conditions or limited backhaul connectivity. The choice between the two types depends on the specific requirements of the network deployment and the desired trade-offs between performance and complexity/cost.

#spj11

Learn more about LTE-A: https://brainly.com/question/30868989

The magnitude of the electric field produced by the line of charge at the given point is 0.50 N/C.

To calculate the electric field at the point (x = 0, y = 0.63 m), we can use the principle of superposition. The electric field produced by a small element of charge on the line can be calculated using the formula for the electric field due to a point charge, which is given by:

dE = k * (dq) / r²

Where dE is the electric field produced by a small charge element dq, k is Coulomb's constant (8.99 x 10^9 N m²/C²), and r is the distance between the charge element and the point where the electric field is being measured. Since the line of charge is infinitely long, we need to integrate the contribution of each charge element along the length of the line.

Considering a small element of charge dq on the line, the distance between this element and the point (x = 0, y = 0.63 m) can be calculated using the Pythagorean theorem. The expression for dq in terms of x can be obtained by considering the linear charge density λ = q / L, where L is the length of the line of charge. Integrating the expression for dE over the entire length of the line and substituting the given values, we can calculate the magnitude of the electric field to be approximately 0.50 N/C.

Learn more about electric field produced by the line of charge:

https://brainly.com/question/32186217

#SPJ11

The angle of incidence in this scenario is 10°.The angle of incidence is the angle between the incident ray (the incoming ray of light) and the normal to the surface it strikes.

In this case, the problem states that the ray of light indexes on a smooth surface and makes an angle of 10° with the surface. Since the angle of incidence is defined as the angle between the incident ray and the normal, and the surface is smooth (presumably meaning it is flat), the normal to the surface would be perpendicular to the surface.

Therefore, the angle of incidence is equal to the angle that the incident ray makes with the surface, which is given as 10°. Hence, the correct answer is option a) 10°.

Learn more about angles of incidence here:

https://brainly.com/question/14221826

#SPJ11

The frequency of an ultraviolet wave with can be calculated using the equation v = c/λ,  the frequency of the ultraviolet wave is approximately 1.36 x 10^15 Hz, which corresponds to the answer option: 1.4 x 10^15 Hz.

The frequency of a wave can be calculated using the formula:

f = c / λ,

where f is the frequency, c is the speed of light, and λ is the wavelength.

Substituting the given wavelength of 220 nm (220 x 10^-9 m) into the equation, and using the speed of light c = 3 x 10^8 m/s, we have:

f = (3 x 10^8 m/s) / (220 x 10^-9 m) = 1.36 x 10^15 Hz.

Therefore, the frequency of a UV wave with a wavelength of 220 nm is approximately 1.36 x 10^15 Hz.

Learn more about frequency here;

https://brainly.com/question/254161

#SPJ11

An airplane starts from west on the runway. The engines extort constant force of 78.0 KN on the body of the plane (mass 9 20 104 Kg) during takeoff . The plane reaches its takeoff speed after traveling approximately 1135.17 meters down the runway.

To find the distance the plane travels down the runway to reach its takeoff speed, we can use the equations of motion.

The force exerted by the engines is given as 78.0 kN, which can be converted to Newtons:

Force = 78.0 kN = 78.0 × 10^3 N

The mass of the plane is given as 9.20 × 10^4 kg.

The acceleration of the plane can be determined using Newton's second law:

Force = mass × acceleration

Rearranging the equation, we have:

acceleration = Force / mass

Substituting the given values, we find:

acceleration = (78.0 × 10^3 N) / (9.20 × 10^4 kg)

Now, we can use the equations of motion to find the distance traveled.

The equation that relates distance, initial velocity, final velocity, and acceleration is

v^2 = u^2 + 2as

where:

v = final velocity = 46.1 m/s (takeoff speed)

u = initial velocity = 0 m/s (plane starts from rest)

a = acceleration (calculated above)

s = distance traveled

Plugging in the values, we have:

(46.1 m/s)^2 = (0 m/s)^2 + 2 × acceleration × s

Simplifying the equation, we can solve for 's':

s = (46.1 m/s)^2 / (2 × acceleration)

Calculating this, we find:

s ≈ 1135.17 m

Therefore, the plane reaches its takeoff speed after traveling approximately 1135.17 meters down the runway.

To learn more about Newton's second law visit: https://brainly.com/question/25545050

#SPJ11

To exert the maximum pressure, the box should be placed in such a way that the force is concentrated on the smallest possible area of the bottom of the box in contact with the table. This can be achieved by placing the box on its edge or on one of its corners.

When a rectangular box is placed on a table, the pressure exerted on the table is the force of the box divided by the area of the bottom of the box in contact with the table. Therefore, to exert the maximum pressure, the box should be placed in such a way that the force is concentrated on the smallest possible area of the bottom of the box in contact with the table. This can be achieved by placing the box on its edge or on one of its corners.

When the box is placed on its edge, only a small area of the bottom of the box is in contact with the table, resulting in a higher pressure.

Similarly, when the box is placed on one of its corners, only a single point of the bottom of the box is in contact with the table, resulting in an even higher pressure.

It is important to note that this method of maximizing pressure is not always desirable as it can damage the table or the box. In practical situations, it is recommended to distribute the weight of the box evenly over the surface of the table to avoid damage and ensure stability.

Learn more about pressure at: https://brainly.com/question/28012687

#SPJ11

The speed of sound in air is approximately 340 meters per second.

To calculate the speed of sound in air, we can use the formula:

Speed of sound = Frequency × Wavelength

Given:

Frequency = 8 kHz = 8,000 Hz

Wavelength = 4.25 cm = 0.0425 m

Plugging in the values:

Speed of sound = 8,000 Hz × 0.0425 m = 340 m/s

Learn more about speed here :-

https://brainly.com/question/17661499

#SPJ11

The height of the side of the cube outside water is approximately 1.46 dm.

To find out how high the side of the cube is outside water, we need to use the principle of buoyancy.

What is the principle of buoyancy?

Buoyancy is the upward force exerted by a fluid that opposes the weight of an immersed object. This principle states that the buoyant force experienced by an object immersed in a fluid is equal to the weight of the fluid displaced by that object. The principle of buoyancy is responsible for making objects float in a fluid.

The formula for buoyancy is as follows:

Buoyant force = weight of the displaced fluid.

Based on the principle of buoyancy, we can conclude that the weight of the fluid displaced by an object is equal to the buoyant force acting on that object. Therefore, the buoyant force acting on an object is given by:

Buoyant force = density of the fluid × volume of the displaced fluid × acceleration due to gravity.

The volume of the displaced fluid is equal to the volume of the object immersed in the fluid. Hence, the buoyant force can also be expressed as:

Buoyant force = density of the fluid × volume of the object × acceleration due to gravity.

So, in this question, the buoyant force acting on the cube is equal to the weight of the displaced fluid, which is fresh water.

The density of fresh water is given to be 1000 kg/m³.

The density of the cube is given to be 750 kg/m³.

The volume of the cube is given to be:

Volume of the cube = side³= (27 cm)³= 19683 cm³= 0.019683 m³

Therefore, the weight of the cube can be calculated as follows:

Weight of the cube = density of the cube × volume of the cube × acceleration due to gravity

= 750 kg/m³ × 0.019683 m³ × 9.8 m/s²= 113.3681 N

The buoyant force acting on the cube can be calculated as follows:

Buoyant force = density of the fluid × volume of the object × acceleration due to gravity

= 1000 kg/m³ × 0.019683 m³ × 9.8 m/s²= 193.5734 N

According to the principle of buoyancy, the buoyant force acting on the cube must be equal to the weight of the cube. Hence, we have:

Buoyant force = Weight of the cube

193.5734 N = 113.3681 N

This implies that the cube is experiencing an upward force of 193.5734 N due to the water.

Therefore, the height of the side of the cube outside water can be calculated as follows:

Weight of the cube = Density of the cube × Volume of the cube × Acceleration due to gravity

Volume of the cube outside water = Volume of the cube inside water

Weight of the cube = Density of water × Volume of the cube outside water × Acceleration due to gravity

Density of water = 1000 kg/m³

Acceleration due to gravity = 9.8 m/s²

Now we can plug in the values to get the height of the side of the cube outside water:

750 kg/m³ × 0.019683 m³ × 9.8 m/s² = 1000 kg/m³ × (0.019683 m³ - Volume of the cube outside water) × 9.8 m/s²

144.5629 N = 9800 m²/s² × (0.019683 m³ - Volume of the cube outside water)

Volume of the cube outside water = (0.019683 m³ - 0.0147481 m³) = 0.0049359 m³

Height of the side of the cube outside water = (Volume of the cube outside water)^(1/3)

Height of the side of the cube outside water = (0.0049359 m³)^(1/3)

Height of the side of the cube outside water ≈ 1.46 dm

Therefore, the height of the side of the cube outside water is approximately 1.46 dm.

Learn more about density:

https://brainly.com/question/952755

#SPJ11