The number of photons emitted per second is 3.63 × 10⁻²¹ photons/s.
The number of photons emitted per second when a 100-W light bulb radiates energy at a rate of 115 J/s with all the light emitted having a wavelength of 545 nm can be calculated as follows:
Firstly, we will calculate the energy per photon:E = hc/λwhere, E = Energy of a photonh = Planck's constant = 6.626 × 10⁻³⁴ Js (joule-second)λ = wavelength of light = 545 nm = 545 × 10⁻⁹ m (meter)c = speed of light = 3 × 10⁸ m/sE = (6.626 × 10⁻³⁴ J s)(3 × 10⁸ m/s)/(545 × 10⁻⁹ m)= 3.63 × 10⁻¹⁹ JE = 3.63 × 10⁻¹⁹ J.
Now, we can calculate the number of photons per second emitted by the light bulb:Power of light = Energy per second/Number of photons per secondP = E/tN = E/PWhere, P = Power of light = 100 W = 100 J/st = Time = 1sE = Energy per photon = 3.63 × 10⁻¹⁹ JN = Number of photons per second= E/P= (3.63 × 10⁻¹⁹ J)/(100 J/s)= 3.63 × 10⁻²¹/s.
Therefore, the number of photons emitted per second is 3.63 × 10⁻²¹ photons/s.
Learn more about photons here,
https://brainly.com/question/31379966
#SPJ11
Sunlight is incident on a diffraction grating that has 3,750 lines/cm. The second-order spectrum over the visible range (400-700 nm) is to be limited to 1.50 cm along a screen that is a distance L from the grating. What is the required value of L?
Sunlight is incident on a diffraction grating that has 3,750 lines/cm. The second-order spectrum over the visible range (400-700 nm) is to be limited to 1.50 cm along a screen that is a distance L from the grating. L = 1.50 cm / tan(atan(1.50 cm / L)).This equation is transcendental and cannot be directly solved algebraically. However, we can use numerical methods or an iterative process to approximate the value of L.
To find the required value of L, we can use the formula for the angular separation of the diffraction orders produced by a diffraction grating:
sin(θ) = mλ/d
where:
θ is the angle between the central maximum and the desired diffraction order, m is the diffraction order (in this case, m = 2 for the second-order spectrum), λ is the wavelength of light, d is the spacing between the lines of the diffraction grating.In this problem, we want to limit the second-order spectrum (m = 2) to 1.50 cm on a screen. We need to find the value of L, the distance between the grating and the screen.
First, we need to calculate the spacing between the lines of the diffraction grating. Given that the grating has 3,750 lines/cm, the spacing (d) between the lines can be expressed as the reciprocal of the lines per unit length:
d = 1 / (3,750 lines/cm) = 1 / (3,750 lines/0.01 m) = 0.01 m / 3,750 lines ≈ 2.67 x 10^(-6) m
Next, we can find the angles (θ1 and θ2) that correspond to the desired wavelengths of light (λ1 = 400 nm and λ2 = 700 nm) in the second-order spectrum. For the second-order, m = 2:
sin(θ) = mλ/d
sin(θ1) = (2)(400 x 10^(-9) m) / (2.67 x 10^(-6) m) ≈ 0.299
sin(θ2) = (2)(700 x 10^(-9) m) / (2.67 x 10^(-6) m) ≈ 0.524
To limit the second-order spectrum to 1.50 cm on the screen, the angular separation between θ1 and θ2 must be equal to the inverse tangent of (1.50 cm / L):
θ2 - θ1 = atan(1.50 cm / L)
Now, we can solve for L:
L = 1.50 cm / tan(θ2 - θ1)
Substituting the values of θ1 and θ2:
L = 1.50 cm / tan(atan(1.50 cm / L))
This equation is transcendental and cannot be directly solved algebraically. However, we can use numerical methods or an iterative process to approximate the value of L.
By using an iterative process or numerical methods, the required value of L can be determined.
To learn more about wavelength visit: https://brainly.com/question/10750459
#SPJ11
It is desired to sample, by means of an ADC, any signal for which the following data is known: The maximum power of the signal reaches 800 mW The minimum power is 0.1 mW. Its maximum frequency reaches 10 kHz.
Determine:
a) The dynamic range (DR) of the signal.
b) The minimum number of bits of resolution (of the ADC) required to avoid distortion and that meets
with the SNR.
c) The conversion time required to satisfy the maximum frequency of the signal
a) The dynamic range (DR) of the signal is approximately 33.98 dB.
b) The minimum number of bits of resolution required for the ADC is 11 bits.
c) The conversion time required to satisfy the maximum frequency of the signal is 0.1 milliseconds.
a) The dynamic range (DR) of a signal is the ratio between the maximum and minimum power levels, expressed in decibels (dB). In this case, the dynamic range can be calculated using the formula DR = 10 * log10(maximum power/minimum power), which results in DR ≈ 33.98 dB.
b) The minimum number of bits of resolution required for the ADC can be determined based on the desired signal-to-noise ratio (SNR). The formula to calculate the required number of bits is N = ceil(log2(4 * SNR)), where SNR is the desired signal-to-noise ratio. Assuming a desired SNR of 6 dB, the minimum number of bits required would be N ≈ 11.
c) The conversion time required to satisfy the maximum frequency of the signal can be determined using the Nyquist-Shannon sampling theorem, which states that the sampling rate should be at least twice the maximum frequency. Therefore, the conversion time can be calculated as 1 / (2 * maximum frequency), resulting in a conversion time of approximately 0.1 milliseconds.
To know more about dynamic range (DR) click here:
https://brainly.com/question/31715117
#SPJ11
How much is vo(t) in the following circuit? vs(t) 5cos(100t) other 4 5 cos(100t) -20 cos(100t) 20 cos(100t) R1 192 •4vs(t) R2 vo(t) 192 1
The expression for v₀(t) (voltage) in the following circuit is v₀(t) = (20cos(100t)) / 1
How to determine voltage?To determine the value of v₀(t) in the given circuit, apply Kirchhoff's voltage law (KVL) and Ohm's law.
Kirchhoff's voltage law states that the sum of the voltage drops around a closed loop in a circuit is equal to the sum of the voltage sources in that loop. In this case, write the following equation using KVL:
-4vs(t) + R1 × (4vs(t) - v₀(t)) + R2 × v₀(t) = 0
Now, substitute the given values:
-4(5cos(100t)) + 192 × (4(5cos(100t)) - v₀(t)) + 1 × v₀(t) = 0
Simplifying the equation further:
-20cos(100t) + 192(20cos(100t) - v₀(t)) + v₀(t) = 0
Expanding and rearranging terms:
-20cos(100t) + 3840cos(100t) - 192v₀(t) + v₀(t) = 0
Combining like terms:
3820cos(100t) - 191v₀(t) = 0
Now, isolate v₀(t) by moving the terms around:
191v₀(t) = 3820cos(100t)
Dividing both sides by 191:
v₀(t) = (3820cos(100t)) / 191
Therefore, the expression for v₀(t) in the circuit is:
v₀(t) = (20cos(100t)) / 1
Find out more on circuit here: https://brainly.com/question/2969220
#SPJ4
A proton in a synchrotron is moving in a circle of radius 1 km and increasing its speed by v(t) = c₁ + c₂t², where c₁ = 8.6 × 10⁵ m/s³ and c₂ = 10⁵ m/s³. a. What is the proton's total acceleration at t = 5.0 s?
a = ________ x 10⁹ m/s² b. At what time does the expression for the velocity become unphysical? t = ______ s
A proton in a synchrotron is moving in a circle of radius 1 km and increasing its speed by v(t) = c₁ + c₂t², where c₁ = 8.6 × 10⁵ m/s³ and c₂ = 10⁵ m/s³
Total acceleration of the proton in the synchrotron when t = 5.0s:
At time t, radius of the circular path is given by: r = 1 km = 10³m
The velocity of the proton is: v(t) = c₁ + c₂t², Where c₁ = 8.6 × 10⁵ m/s³ and c₂ = 10⁵ m/s³
When t = 5.0 s, velocity of the proton is: v(t) = c₁ + c₂t²= 8.6 × 10⁵ m/s³ + 10⁵ m/s³ × (5.0 s)²= 8.6 × 10⁵ m/s³ + 2.5 × 10⁷ m/s= 2.58 × 10⁷ m/s
So the tangential acceleration of the proton is given by:
aₜ = dv/dt = 2c₂t= 2 × 10⁵ m/s³ × 5.0 s= 10⁶ m/s²
The centripetal acceleration of the proton is given by: aₙ = v²/r= (2.58 × 10⁷ m/s)²/(10³ m)= 6.65 × 10¹² m/s²
The total acceleration of the proton when t = 5.0s is given by: a = √(aₙ² + aₜ²)= √[(6.65 × 10¹² m/s²)² + (10⁶ m/s²)²]= √[4.42 × 10²⁵ m²/s⁴ + 10¹² m²/s⁴]= √(4.42 × 10²⁵ + 10¹²) m²/s⁴= 2.1 × 10¹² m/s² (rounded to one significant figure)
Therefore, the total acceleration of the proton at t = 5.0 s is 2.1 × 10¹² m/s².
The expression for the velocity becomes unphysical when: v(t) = c₁ + c₂t² = c (say)
For this expression to be unphysical, it would imply that the speed of the proton is greater than the speed of light. This is impossible and indicates that the expression for velocity has lost its physical significance. Therefore, when v(t) = c (say)
It implies that v(t) > c (speed of light)
Let's equate v(t) to c:v(t) = c₁ + c₂t² = c10⁵ m/s³t² + 8.6 × 10⁵ m/s³ = c
The time at which the velocity of the proton becomes unphysical can be obtained by solving for t in the above equation: 10⁵ m/s³t² + 8.6 × 10⁵ m/s³ = c10⁵ m/s³t² = c - 8.6 × 10⁵ m/s³t = sqrt((c - 8.6 × 10⁵ m/s³)/10⁵ m/s³)
The expression for velocity becomes unphysical when the time, t is: sqrt((c - 8.6 × 10⁵ m/s³)/10⁵ m/s³) seconds (rounded to two significant figures)
Therefore, the time at which the expression for the velocity becomes unphysical is sqrt ((c - 8.6 × 10⁵ m/s³)/10⁵ m/s³) seconds.
Here's another question on a proton to interest you: https://brainly.com/question/30509265
#SPJ11
Charges moving in a uniform magnetic field are subject to the same magnetic force regardless of their direction of motion Select one o True o False
The correct statement between the following options is: Charges moving in a uniform magnetic field are subject to the same magnetic force regardless of their direction of motion. True
How magnetic field affect a moving charge? When a charged particle is moving in a magnetic field, it experiences a magnetic force that acts perpendicularly to the direction of motion of the charge and to the direction of the magnetic field. The magnetic force that acts on the charge is responsible for changing the velocity of the charge in a manner that causes the particle to move in a circular path.The magnitude of the magnetic force is proportional to the magnitude of the charge, the velocity of the charge, and the magnetic field strength. The direction of the magnetic force can be determined using the right-hand rule.
Learn more about a magnetic field:
https://brainly.com/question/14411049
#SPJ11
Select the correct answer.
In which item is energy stored in the form of gravitational potential energy?
A.
a slice of bread
B.
a compressed spring
C.
an apple on a tree
D.
a stretched bow string
Reset Next
C. an apple on a tree as energy stored in the form of gravitational potential energy.
Gravitational potential energy is a form of energy that an object possesses due to its position in a gravitational field.
It is directly related to the height or vertical position of the object relative to a reference point.
Out of the given options, only the apple on a tree possesses gravitational potential energy because it is located above the ground.
As the apple is raised higher on the tree, its gravitational potential energy increases accordingly.
Thus, option C, "an apple on a tree," is the correct choice.
To learn more about Gravitational potential energy,
https://brainly.com/question/15896499
Given the:
D = 2r cos θ aθ – sen θ / 3r as
In cylindrical coordinates, find the flux that crosses the portion of the plane z=0 defined by r ≤ a , 0≤ ϕ ≤ π/2.
Repeat the exercise for 3π/2 ≤ ϕ ≤ π/2.
Assume that the positive flux has the direction of `az´
answer: -a/3, a/3
The flux crossing the portion of the plane z=0 defined by r ≤ a and 0 ≤ ϕ ≤ π/2 is (2/3) a³ in the direction of az.
The flux crossing the portion of the plane z=0 defined by r ≤ a and 3π/2 ≤ ϕ ≤ π/2 is -(2/3) a³ in the direction of az.
Hence, the answers are: For 0 ≤ ϕ ≤ π/2: Φ = (2/3) a³ and For 3π/2 ≤ ϕ ≤ π/2: Φ = -(2/3) a³
To calculate the flux crossing the portion of the plane defined by the conditions, we need to evaluate the surface integral of the flux density vector over the specified region.
The flux density vector D in cylindrical coordinates as D = 2r cos θ aθ - sin θ / 3r as, we can write the flux integral as:
Φ = ∫∫S D · dA
where S represents the surface of the specified region and dA is the differential area vector.
For the first case, where 0 ≤ ϕ ≤ π/2, the surface S can be parameterized as follows:
r = ρ
ϕ = θ, where 0 ≤ ρ ≤ a and 0 ≤ θ ≤ π/2
The differential area vector dA can be expressed as dA = ρ dρ dθ az, where az is the unit vector in the z-direction.
Substituting the values into the flux integral, we have:
Φ = ∫∫S D · dA
= ∫₀ᵃ ∫₀^(π/2) (2ρ cos θ aθ - sin θ / 3ρ as) · (ρ dρ dθ az)
Expanding the dot product and simplifying the expression, we obtain:
Φ = ∫₀ᵃ ∫₀^(π/2) (2ρ² cos θ dρ dθ) / 3
Integrating with respect to ρ first, we get:
Φ = ∫₀^(π/2) [(2/3) ρ³ cos θ] ₍ₐ₀₎ dθ
= (2/3) a³ ∫₀^(π/2) cos θ dθ
= (2/3) a³ [sin θ] ₍ₐ₀₎
= (2/3) a³ [sin (π/2) - sin 0]
= (2/3) a³
For the second case, where 3π/2 ≤ ϕ ≤ π/2, we can use the same approach but with different limits of integration for ϕ:
r = ρ
ϕ = θ, where 0 ≤ ρ ≤ a and 3π/2 ≤ θ ≤ π/2
Following the same steps as before, we find:
Φ = ∫₀ᵃ ∫₃π/₂^π/₂ (2ρ² cos θ dρ dθ) / 3
= -(2/3) a³
To knwo more about flux crossing
https://brainly.com/question/32812814
#SPJ11
A block of wood and a 0.90 kg block of steel are placed in thermal contact while thermally isolated from their surroundings.
If the wood was at an initial temperature of 40°C, the steel was at an initial temperature of 60°C, and the final equilibrium temperature of the wood and steel was 45°C then what was the mass of the block of wood? (to 2 s.f and in kg)
[cwood = 2400 J kg−1 K−1, csteel = 490 J kg−1 K−1]
The mass of the block of wood is 0.40 kg. The formula to calculate the thermal equilibrium is given as:
Q = mcΔT
Here, Q represents the heat transferred between two bodies,
m represents the mass of the object,
c represents the specific heat of the material of the object, and
ΔT is the temperature difference between the final and initial temperature of the object.
For the wood:
Q1 = m1c1ΔT1
Q1 = m1 * 2400 * (45 - 40)
Q1 = m1 * 12000 Joules
For the steel:
Q2 = m2c2ΔT2
Q2 = m2 * 490 * (45 - 60)
Q2 = -m2 * 7350 Joules
As no heat is exchanged between the bodies and their surroundings, so the heat gained by one body is equal to the heat lost by the other body.
(Q1)gain = (Q2)loss
m1 * 12000 = -m2 * 7350
Now, substituting the given values in the above equation, we get:
m1 = 0.40 kg. 2 s.f.
Answer: 0.40 kg.
To leran more about thermal equilibrium, refer:-
https://brainly.com/question/29419074
#SPJ11
During a collision with the floor, the velocity of a 0.200-kg ball changes from 28 m/s downward toward the floor to 17 m/s upward away from the wall. If the time the ball was in contact with the floor was 0.075 seconds, what was the magnitude of the average force of impact? Answer in positive newtons.
The force of impact on average during the collision on the ball is 120N. The force of impact is the force that occurs when two objects collide. It is calculated by multiplying the mass of the object and its acceleration.
The formula for force is: F = ma. Here, m = 0.200 kgV1 = -28 m/sV2 = 17 m/st = 0.075 seconds Initial velocity, u = -28 m/s Final velocity, v = 17 m/s Change in velocity, Δv = v - u = 17 - (-28) = 45 m/s The acceleration during the collision is given bya = Δv/t = 45/0.075 = 600 m/s²To calculate the force of impact, we need to use the formula: F = ma = 0.200 × 600F = 120 N. Therefore, the magnitude of the average force of impact is 120 N.
Learn more about force of impact:
https://brainly.com/question/12912354
#SPJ11
Does the induced voltage, V im
, in a coil of wire depend upon the resistance of the wire used to make the coil? Does the amount of induced current flow through the coil depend upon the resistance of the wire used to make the coil? Explain your answers. Suppose you have a wire loop that must be placed in an area where there is magnetic field that is constantly changing in magnitude, but you do not want an induced V ind
in the coil., How would you place the coil in relation to the magnetic field to assure there was no induced (V in
) in the coil?
If the magnetic flux through the coil is kept constant, no voltage will be induced in the coil regardless of the resistance of the wire used to make the coil.
Yes, the induced voltage, Vim, in a coil of wire depends on the resistance of the wire used to make the coil.
The amount of induced current flow through the coil also depends on the resistance of the wire used to make the coil. This is because the greater the resistance of the wire, the greater the amount of voltage needed to create a current of the same strength.
A wire loop can be placed in an area where there is a constantly changing magnetic field in magnitude, but with no induced Vind, by placing it in such a way that the magnetic flux passing through the coil is minimized. One way to do this is to place the coil at a right angle to the direction of the magnetic field.
Another way is to move the coil outside the area of changing magnetic field.
However, if the magnetic flux through the coil is kept constant, no voltage will be induced in the coil regardless of the resistance of the wire used to make the coil.
To learn about magnetic fields here:
https://brainly.com/question/14411049
#SPJ11
Q6. Explain what the difference is between an
asteroid, a rocky planet, a gas giant, a brown dwarf and a star.
[10 pts]
Asteroids, rocky planets, gas giants, brown dwarfs, and stars are all different celestial objects in the universe. Each of these objects has different characteristics that distinguish them from one another.
The difference between an asteroid, a rocky planet, a gas giant, a brown dwarf, and a star are explained below.
Asteroids: Asteroids are small, rocky objects that orbit the Sun. They are too small to be classified as planets, but too large to be classified as meteoroids. Most asteroids are found in the asteroid belt between Mars and Jupiter.
Some of the largest asteroids in the asteroid belt are Ceres, Vesta, and Pallas.
Rocky Planets: Rocky planets are terrestrial planets that are composed primarily of rock and metal. They have solid surfaces and are relatively small compared to gas giants.
The rocky planets in our solar system are Mercury, Venus, Earth, and Mars.Gas Giants: Gas giants are planets that are composed primarily of hydrogen and helium. They are much larger than rocky planets and have thick atmospheres. The gas giants in our solar system are Jupiter, Saturn, Uranus, and Neptune.
Brown Dwarfs: Brown dwarfs are objects that are too small to be stars, but too large to be gas giants. They are also known as failed stars because they do not have enough mass to sustain nuclear fusion in their cores.
Stars: Stars are massive, luminous objects that are held together by gravity.
They generate energy through nuclear fusion in their cores. There are many different types of stars, ranging from small red dwarfs to massive blue giants. The Sun is a typical yellow dwarf star.
Asteroids, rocky planets, gas giants, brown dwarfs, and stars are all different celestial objects with unique characteristics. Asteroids are small, rocky objects that orbit the Sun.
Rocky planets are terrestrial planets that are composed primarily of rock and metal, while gas giants are planets that are composed primarily of hydrogen and helium.
Brown dwarfs are objects that are too small to be stars, but too large to be gas giants, and stars are massive, luminous objects that generate energy through nuclear fusion in their cores. Understanding the differences between these celestial objects is important for astronomers to study the universe and its history.
To know more about nuclear fusion :
brainly.com/question/14019172
#SPJ11
A 110 g hockey puck sent sliding over ice is stopped in 12.1 m by the frictional force on it from the ice. (a) If its initial speed is 6.3 m/s, what is the magnitude of the frictional force? (b) What is the coefficient of friction between the puck and the ice?
(a) the magnitude of the frictional force acting on the hockey puck is 0.19 N.
(b) The coefficient of friction between the puck and the ice is 0.18.
Given, Mass of the hockey puck m = 110 g = 0.11 kg
Initial speed of the hockey puck u = 6.3 m/s
Final speed of the hockey puck v = 0
Distance covered by the hockey puck s = 12.1 m
(a) To calculate the magnitude of the frictional force, we need to calculate the deceleration of the hockey puck.
Using the third equation of motion, v² = u² + 2as
Here, u = 6.3 m/s, v = 0, s = 12.1 m
a = (v² - u²) / 2s
= (0 - (6.3)²) / 2(-12.1)
a = -1.72 m/s²
The frictional force acting on the hockey puck is given by frictional force, f = ma = 0.11 kg × 1.72 m/s² = 0.19 N
(b) To calculate the coefficient of friction between the puck and the ice, we need to use the equation of frictional force.
f = μN
Here, N is the normal force acting on the hockey puck, which is equal to its weight N = mg = 0.11 kg × 9.81 m/s² = 1.08 N.
Substituting the values of f and N,0.19 N = μ × 1.08 N
μ = 0.18
To learn more about frictional force, refer:-
https://brainly.com/question/30280206
#SPJ11
A1 to bintang ball that is mading at 2.90 m* tres her pool table and bounces straight back * 2.2 ts original soced). The colorata 700 (tume that the same as me pestive direction Calculate the weagufurca { act on the body the burre te direction at the spot worrower ) ( How much kinetic roergy in joules is het during the contre magte (what percent of the origin?
When a ball of mass 2.90 kg strikes a pool table and bounces straight back with a speed of 2.2 m/s, the change in momentum can be calculated by subtracting the initial momentum from the final momentum.
The weight force acting on the ball can be determined by multiplying the mass of the ball by the acceleration due to gravity. The kinetic energy lost during the collision can be calculated as the difference between the initial kinetic energy and the final kinetic energy. The percentage of the original kinetic energy lost can be found by dividing the lost kinetic energy by the initial kinetic energy and multiplying by 100.
To determine the change in momentum of the ball, we subtract the final momentum from the initial momentum. The initial momentum is given by the product of the mass and the initial velocity, which is 2.90 kg * 0 m/s since the ball is at rest. The final momentum is given by the product of the mass and the final velocity, which is 2.90 kg * (-2.2 m/s) since the ball bounces back in the opposite direction.
The weight force acting on the ball can be calculated by multiplying the mass of the ball (2.90 kg) by the acceleration due to gravity (approximately 9.8 m/s^2). This will give us the weight force in Newtons.
To calculate the kinetic energy lost during the collision, we subtract the final kinetic energy from the initial kinetic energy. The initial kinetic energy is given by (1/2) * mass * (initial velocity)^2, and the final kinetic energy is given by (1/2) * mass * (final velocity)^2.
Learn more abut kinetic energy here:
https://brainly.com/question/999862
#SPJ11
Suppose that we replaced a fleet of 500000 intemal combustion cars (operating with 15% efficiency) presently on the road with electric cars (operating with 40% efficiency). Assume that the average motive power of both kinds of car is the same and equal to 9000 W. and assume that the average car is driven 450 hours per year. First calculate the number of gallons of gasoline used by the intemal combustion fleet during one year. Second assume that the electricity used by the fleet of electric cars is produced by an oil-fired turbine generator operating at 38% efficiency and calculate the number of gallons of fuel needed to produce this electrical energy (for simplicity, just assume the energy equivalent of this fuel is equal to that of gasoline). [Obviously, this is an artificial problem; in real life, this would not be the source of the cars' electrical energy.) Compare the amount of fossil fuel needed in cach case,
Assume that the average motive power of both kinds of car is the same and equal to 9000 W. and assume that the average car is driven 450 hours per year.The electric car fleet would require approximately 45,644 gallons of gasoline (equivalent energy) to produce the electrical energy needed for one year.
Let's break down the calculations and compare the amount of fossil fuel needed in each case.
First, let's calculate the number of gallons of gasoline used by the internal combustion fleet during one year. To do this, we need to determine the total energy consumed by the fleet and convert it to the equivalent amount of gasoline.
The internal combustion fleet consumes:
Energy = Power × Time = 9000 W × 450 hours = 4,050,000 Wh
Converting Wh to gallons of gasoline:
1 gallon of gasoline is approximately equivalent to 33.7 kWh of energy.
Energy in gallons of gasoline = (4,050,000 Wh) / (33.7 kWh/gallon) = 120,236 gallons
Therefore, the internal combustion fleet would use approximately 120,236 gallons of gasoline during one year.
Next, let's calculate the number of gallons of fuel needed to produce the electrical energy for the electric car fleet. Assuming the electricity is produced by an oil-fired turbine generator operating at 38% efficiency, we need to determine the total energy consumption of the electric car fleet and convert it to the equivalent amount of gasoline.
The electric car fleet consumes:
Energy = Power × Time = 9000 W × 450 hours = 4,050,000 Wh
Converting Wh to gallons of gasoline (considering the generator's efficiency):
1 gallon of gasoline is equivalent to 33.7 kWh of energy.
Considering the generator's efficiency of 38%, we need to consider the ratio of useful energy to the energy input:
Useful energy = Energy consumed × Generator efficiency = 4,050,000 Wh × 0.38 = 1,539,000 Wh
Energy in gallons of gasoline = (1,539,000 Wh) / (33.7 kWh/gallon) = 45,644 gallons
Therefore, the electric car fleet would require approximately 45,644 gallons of gasoline (equivalent energy) to produce the electrical energy needed for one year.
Comparing the amount of fossil fuel needed in each case:
Internal combustion fleet: Approximately 120,236 gallons of gasoline per year. Electric car fleet: Approximately 45,644 gallons of gasoline (equivalent energy) per yearBased on these calculations, the electric car fleet would require significantly less fossil fuel compared to the internal combustion fleet, making it a more efficient and environmentally friendly option.
To learn more about power visit: https://brainly.com/question/11569624
#SPJ11
A piston cylinder with a cross-sectional size of 0.02 m² and a mass of 100 kg is resting on the stops. With an outside pressure of 140 kPa, what should be the water pressure to lift the piston? (Take g = 9.81 m/s²) O a. 189 kPa O b. 112 kPa O c. 198 kPa O d. 318 kPa
To lift the piston, the water pressure should be 189 kPa.
To solve this problem, we can use the principle of Pascal's law, which states that the pressure applied to a fluid is transmitted uniformly in all directions. Given that the piston cylinder is resting on the stops, it means that the outside pressure (140 kPa) is being applied to the entire cross-sectional area of the piston.
To lift the piston, the water pressure should be equal to or greater than the outside pressure. By applying Pascal's law, we can calculate the water pressure using the formula:
Water Pressure = Outside Pressure + (Weight of the Piston / Area of the Piston)
The weight of the piston can be calculated using the formula:
Weight = Mass * Acceleration due to gravity
Substituting the given values:
Weight = 100 kg * 9.81 m/s² = 981 N
Now, let's calculate the water pressure:
Water Pressure = 140 kPa + (981 N / 0.02 m²) = 140 kPa + 49050 Pa = 140 kPa + 49.05 kPa = 189.05 kPa
Rounded to the nearest whole number, the water pressure required to lift the piston is approximately 189 kPa.
To know more about water pressure click here:
https://brainly.com/question/32181383
#SPJ11
The Intemational Space Station is orbiting at an altitude of about 231 miles ( 370 km) above the earth's surface. The mass of the earth is 5.976×10 24
kg and the radius of the earth is 6.378×10 6
m. a) Assuming a circular orbit, calculate the orbital speed (in m/s ) of the space station? (5pts) b) Calculate the orbital period (in minutes) of the space station. (5pts) c) Convert the orbital speed obtained in part (a) from m/s to miles/hour. You should get something close to 17000 mileshour. Hint: 1 mile =1.6 km.
a) The orbital speed of the International Space Station is approximately 7.66 km/s. b) The orbital period of the space station is approximately 92.68 minutes. c) Converting the orbital speed from m/s to miles/hour yields approximately 17144 miles/hour.
a) The orbital speed of an object in a circular orbit can be calculated using the formula v = √(G * M / r), where v is the orbital speed, G is the gravitational constant, M is the mass of the Earth, and r is the distance from the center of the Earth to the object. Plugging in the given values, we get v = √((6.67430 × 10^(-11) m³/(kg·s²)) * (5.976 × 10^(24) kg) / (6.378 × 10^(6) m + 370 × 10^(3) m)) ≈ 7.66 km/s.
b) The orbital period can be calculated using the formula T = (2πr) / v, where T is the orbital period, r is the distance from the center of the Earth to the object, and v is the orbital speed. Plugging in the values, we get T = (2π * (6.378 × 10^(6) m + 370 × 10^(3) m)) / (7.66 km/s * 1000 m/km) ≈ 92.68 minutes.
c) To convert the orbital speed from m/s to miles/hour, we use the conversion factor 1 mile = 1.6 km. Thus, the orbital speed in miles/hour is approximately 7.66 km/s * (3600 s/hour) * (1 mile / 1.6 km) ≈ 17144 miles/hour.
Learn more about orbital speed here:
https://brainly.com/question/12449965
#SPJ11
The value of current in a 73- mH inductor as a function of time is: I=7t 2
−5t+13 where I is in amperes and t is in seconds. Find the magnitude of the induced emf at t=6 s. Write your answer as the magnitude of the emf in volts. Question 7 1 pts The circuit shows an R-L circuit in which a battery, switch, inductor and resistor are in series. The values are: resistor =52Ω, inductor is 284mH, battery is 20 V. Calculate the time after connecting the switch after which the current will reach 42% of its maximum value. Write your answer in millseconds.
Part 1: The magnitude of the induced emf at t = 6 seconds is 5.767 V.
Part 2: The time after connecting the switch after which the current will reach 42% of its maximum value is 8.9 ms.
Part 1 :
The current as a function of time is given by, I = 7t²−5t+13
Given, t = 6 secondsTherefore, the current at t = 6 seconds is, I = 7(6)² - 5(6) + 13I = 264 A
Therefore, the magnitude of the induced emf is given by,ε = L(dI/dt)At t = 6 seconds, I = 264
Therefore, dI/dt = 14t - 5Therefore, dI/dt at t = 6 seconds is, dI/dt = 14(6) - 5dI/dt = 79
The inductance L = 73 mH = 0.073 H
Therefore, the magnitude of the induced emf at t = 6 seconds is,ε = L(dI/dt)ε = 0.073(79)ε = 5.767 V
Therefore, the magnitude of the induced emf at t = 6 seconds is 5.767 V.
Part 2:
Given, resistor = 52 Ωinductor, L = 284 mH = 0.284 Hbattery, V = 20 VWhen the switch is closed, the inductor starts to charge, and the current increases with time until it reaches a maximum value.
Let this current be I_max.
After closing the switch, the current at any time t is given by, I = (V/R) (1 - e^(-Rt/L))
Where V is the battery voltage, R is the resistance of the resistor, L is the inductance and e is the base of the natural logarithm.
The maximum current that can flow in the circuit is given by, I_max = V/RTherefore, I/I_max = (1 - e^(-Rt/L))
So, when I/I_max = 0.42 (42% of its maximum value), e^(-Rt/L) = 0.58
Taking natural logarithm on both sides, we get,-Rt/L = ln(0.58)t = (-L/R) ln(0.58)t = (-0.284/52) ln(0.58)t = 0.0089 s = 8.9 ms
Therefore, the time after connecting the switch after which the current will reach 42% of its maximum value is 8.9 ms.
To learn about magnitude here:
https://brainly.com/question/30337362
#SPJ11
An AC generator supplies an rms voltage of 115 V at 60.0 Hz. It is connected in series with a 0.200 H inductor, a 4.70 uF capacitor and a 216 12 resistor. What is the impedance of the circuit?
What is the average power dissipated in the circuit?
What is the peak current through the resistor? What is the peak voltage across the inductor?
What is the peak voltage across the capacitor? The generator frequency is now changed so that the circuit is in resonance. What is that new (resonance) frequency?
the impedance of the circuit is approximately 216.588 Ω.the average power dissipated in the circuit is approximately 61.083 W. the new resonance frequency is approximately 148.752 Hz.
To find the impedance of the circuit, we can use the formula:
Z = √(R² + (Xl - Xc)²)
Where:
Z is the impedance
R is the resistance
Xl is the inductive reactance
Xc is the capacitive reactance
Given:
R = 216 Ω
L = 0.200 H
C = 4.70 μF
f = 60.0 Hz
First, we need to calculate the values of inductive reactance (Xl) and capacitive reactance (Xc):
Xl = 2πfL
= 2π * 60.0 * 0.200
≈ 75.398 Ω
Xc = 1 / (2πfC)
= 1 / (2π * 60.0 * 4.70 * 10^(-6))
≈ 56.650 Ω
Now, let's calculate the impedance:
Z = √(R² + (Xl - Xc)²)
= √(216² + (75.398 - 56.650)²)
≈ √(46656 + 353.4106)
≈ √(46909.4106)
≈ 216.588 Ω
Therefore, the impedance of the circuit is approximately 216.588 Ω.
To find the average power dissipated in the circuit, we can use the formula:
P = Vrms² / Z
Where:
P is the average power
Vrms is the rms voltage
Z is the impedance
Given:
Vrms = 115 V
Let's calculate the average power:
P = (115²) / 216.588
≈ 61.083 W
Therefore, the average power dissipated in the circuit is approximately 61.083 W.
The peak current (Ipeak) through the resistor is the same as the rms current, which can be calculated using Ohm's Law:
Ipeak = Vrms / R
= 115 / 216
≈ 0.532 A
Therefore, the peak current through the resistor is approximately 0.532 A.
The peak voltage across the inductor (Vpeak) can be calculated using the formula:
Vpeak = Ipeak * Xl
= 0.532 * 75.398
≈ 40.057 V
Therefore, the peak voltage across the inductor is approximately 40.057 V.
The peak voltage across the capacitor (Vpeak) can be calculated using the formula:
Vpeak = Ipeak * Xc
= 0.532 * 56.650
≈ 30.117 V
Therefore, the peak voltage across the capacitor is approximately 30.117 V.
When the circuit is in resonance, the inductive reactance (Xl) and capacitive reactance (Xc) are equal, and their sum becomes zero. The resonance frequency (fr) can be calculated using the formula:
fr = 1 / (2π√(LC))
Given:
L = 0.200 H
C = 4.70 μF
Let's calculate the resonance frequency:
fr = 1 / (2π√(LC))
= 1 / (2π√(0.200 * 4.70 * 10^(-6)))
≈ 148.752 Hz
Therefore, the new resonance frequency is approximately 148.752 Hz.
Learn more about impedance here:
https://brainly.com/question/30475674
#SPJ11
A spaceship whose rest length is 452 m has a speed of 0.86c with respect to a certain reference frame. A micrometeorite, also with a speed of 0.86c in this frame, passes the spaceship on an antiparallel track. How long does it take this object to pass the spaceship as measured on the ship? Number Units
A spaceship whose rest length is 452 m has a speed of 0.86c with respect to a certain reference frame. it takes approximately 234.09 meters of distance for the micrometeorite to pass the spaceship as measured on the ship.
To determine the time it takes for the micrometeorite to pass the spaceship as measured on the ship, we can use the concept of time dilation from special relativity.
The time dilation formula is given by: Δt' = Δt / γ, where Δt' is the time interval measured on the moving spaceship, Δt is the time interval measured in the rest frame (reference frame), and γ is the Lorentz factor.
In this case, both the spaceship and the micrometeorite have a speed of 0.86c relative to the reference frame. The Lorentz factor can be calculated using the formula: γ = 1 / sqrt(1 - (v^2 / c^2)), where v is the velocity of the objects relative to the reference frame and c is the speed of light.
Plugging in the values, we have: γ = 1 / sqrt(1 - (0.86c)^2 / c^2) ≈ 1.932.
Since the rest length of the spaceship is given as 452 m, the time it takes for the micrometeorite to pass the spaceship as measured on the ship is: Δt' = Δt / γ = 452 m / 1.932 ≈ 234.09 m.
Therefore, it takes approximately 234.09 meters of distance for the micrometeorite to pass the spaceship as measured on the ship.
Learn more about time dilation here:
https://brainly.com/question/30493090
#SPJ11
Frogs have changed their coloring over time to adapt to their environment. This is an example of which of the following?
Adaptation
Artificial selection
Environmental change
Natural selection
Correct option is D. Natural selection.
Frogs have changed their coloring over time to adapt to their environment. This is an example of natural selection.
Natural selection is the process of adaptation in response to environmental change.
The process involves differential survival and reproduction of individuals with genetic traits that are better suited to their environment, and this process can lead to changes in the genetic makeup of a population over time.
As a result, populations of organisms can become better adapted to their environment, which is a critical factor in their survival and continued evolution.
Frogs are known for their remarkable ability to change color to match their surroundings.
This adaptation allows them to blend in with their environment, making them less visible to predators and prey.
The process by which frogs have adapted to their environment is an excellent example of natural selection in action.
Over time, the individuals with genetic traits that provide better camouflage are more likely to survive and reproduce, passing on their traits to their offspring.
As a result, the population of frogs becomes better adapted to their environment, allowing them to thrive in their natural habitats.
The correct Option is D. Natural selection.
For more questions on environment
https://brainly.com/question/1186120
#SPJ8
A person pulls on a cord over a pulley attached to a 3.2 kg block as shown, accelerating the block at a constant 1.2 m/s 2
. What is the force exerted by the person on the rope? Enter your answer in Newtons.
The force exerted by the person on the rope is 3.84 Newtons. According to Newton's second law of motion, the net force acting on an object is equal to its mass multiplied by its acceleration.
The mass of the block is given as 3.2 kg, and the acceleration is given as 1.2 [tex]m/s^2[/tex]. Therefore, the net force acting on the block can be calculated as:
Net force = mass × acceleration
= 3.2 kg × 1.2 [tex]m/s^2[/tex]
= 3.84 N
Since the person is pulling on the cord, the force exerted by the person on the rope is equal to the net force acting on the block. Therefore, the force exerted by the person on the rope is 3.84 Newtons.
Learn more about acceleration here:
https://brainly.com/question/12550364
#SPJ11
A single-phase 40-kVA, 2000/500-volt, 60-Hz distribution transformer is used as a stepdown transformer. Winding resistances are R1 = 2 Ω and R2 = 0.125 Ω; leakage reactances are X1 = 8 Ω and X2 = 0.5 Ω. The load resistance on the secondary is 12 Ω. The applied voltage at the terminals of the primary is 1000 V. (a) Replace all circuit elements with perunit values. (b) Find the per-unit voltage and the actual voltage V2 at the load terminals of the transformer
The problem involves a single-phase distribution transformer with specified ratings and parameters. The task is to convert the circuit elements to per-unit values and calculate the per-unit voltage and the actual voltage at the load terminals of the transformer.
In the given problem, a single-phase 40-kVA, 2000/500-volt, 60-Hz distribution transformer is considered. The transformer is used as a step-down transformer, and its winding resistances and leakage reactances are provided. The load resistance on the secondary side is given as 12 Ω, and the applied voltage at the primary terminals is 1000 V.
To analyze the transformer on a per-unit basis, all circuit elements need to be converted to per-unit values. This involves dividing the actual values by the base values. The base values are typically chosen as the rated values of the transformer. In this case, the base values can be taken as 40 kVA, 2000 volts, and 12 Ω.
By dividing the actual values of resistances and reactances by their corresponding base values, the per-unit values can be obtained. Similarly, the load resistance on the secondary side can be expressed per per-unit by dividing it by the base resistance. After converting the circuit elements to per-unit values, the per-unit voltage can be calculated by dividing the applied voltage at the primary terminals by the base voltage. This provides a relative value that can be used for further calculations.
To find the actual voltage at the load terminals of the transformer, the per-unit voltage is multiplied by the base voltage. This gives the actual voltage value in volts. In conclusion, the problem involves converting the circuit elements of a distribution transformer to per-unit values and calculating the per-unit voltage and the actual voltage at the load terminals. This analysis allows for a standardized representation of the transformer's parameters and facilitates further calculations and comparisons.
Learn more about transformer here:- brainly.com/question/15200241
#SPJ11
An ultra-fast pulse lasers emits pulses of 13 fs. The length of each pulse train is: A) 7.79 pm B) 3.9 pm C) 19.49 pm D 11.69 pm ) E) 3.9 pm Air
An ultra-fast pulse lasers emits pulses of 13 fs. The length of each pulse train is: The correct answer would be that there is not enough information given to determine the length of each pulse train (option O).
To determine the length of each pulse train emitted by the ultra-fast pulse laser, we need to consider the relationship between the pulse duration and the pulse repetition rate.
The length of each pulse train is given by the formula:
Length of each pulse train = Pulse duration × Pulse repetition rate
The pulse duration is provided as 13 fs (femtoseconds). However, the pulse repetition rate is not given in the question. Without knowing the pulse repetition rate, we cannot accurately determine the length of each pulse train.
Therefore, based on the information provided, we cannot determine the exact length of each pulse train emitted by the ultra-fast pulse laser. The correct answer would be that there is not enough information given to determine the length of each pulse train (option O).
Learn more about laser here:
https://brainly.com/question/27853311
#SPJ11
please help me asnwering this question..!
5) D/C Transformer The input voltage to a transformer is \( 120 \mathrm{~V} \mathrm{DC} \) to the primary coil of 1000 turns. What are the number of turns in the secondary needed to produce an output
Approximately 83.33 turns are needed in the secondary coil to produce an output voltage of 10 VDC in this D/C transformer.
In a transformer, the ratio of the number of turns in the primary coil to the number of turns in the secondary coil determines the voltage transformation. To calculate the number of turns in the secondary coil, we can use the formula:
[tex]Turns_{ratio} = (Voltage_{ratio})^{exponent}[/tex]
In this case, the voltage ratio is the ratio of the output voltage to the input voltage. The exponent is 1 since it's a D/C transformer. So, the equation becomes:
(120 VDC) / (10 VDC) = (1000 turns) / (x turns)
Solving for x, the number of turns in the secondary coil, we find:
x = (1000 turns) * (10 VDC) / (120 VDC)
x ≈ 83.33 turns
Therefore, approximately 83.33 turns are needed in the secondary coil to produce an output voltage of 10 VDC in this D/C transformer.
Learn more about voltage here:
https://brainly.com/question/13396105
#SPJ11
The complete question is:
D/C Transformer The input voltage to a transformer is 120 VDC to the primary coil of 1000 turns. What are the number of turns in the secondary needed to produce an output voltage of 10 VDC ?
For a single slit diffraction, what is the equations to calculate the distance from the center of diffraction to the:
a.) 2nd Min
b.) 3rd Min
c.) 1st Secondary Max
d.) 2nd Secondary Max
e.) 4th Secondary Max
I'm really confused on how to find the equations.
For a single slit diffraction pattern, the equations to calculate the distances from the center of diffraction to various points are as follows:
a) The distance to the 2nd minimum (dark fringe) is given by: y₂ = (2λL) / d
b) The distance to the 3rd minimum can be calculated using the same formula, replacing the subscript 2 with 3:
y₃ = (3λL) / d
c) The distance to the 1st secondary maximum (bright fringe) is given by:
y₁ = (λL) / d
d) The distance to the 2nd secondary maximum can be calculated as: y₂' = (2λL) / d
e) The distance to the 4th secondary maximum can be calculated using the same formula as in part d, replacing the subscript 2 with 4:
y₄' = (4λL) / d
These equations give the distances from the center of diffraction pattern to the specified points based on the parameters of single slit diffraction experiment.
Learn more about diffraction here:
https://brainly.com/question/29451443
#SPJ11
Three long, parallel wires carry equal currents of I=4.00 A. In a top view, the wires are located at the corners of a square with all currents flowing upward, as shown in the diagram. Determine the magnitude and direction of the magnetic field at a. the empty corner. b. the centre of the square.
(a) The magnitude of the magnetic field at the empty corner is 3π x 10⁻⁷/d, T.
(b) The magnitude of the magnetic field at the center of the square is 0.
What is the magnitude of the magnetic field?(a) The magnitude of the magnetic field at the empty corner is calculated as;
B = μ₀I/2πd
where;
μ₀ is permeability of free spaceI is the currentd is the distance of the wiresThe resultant magnetic field at the empty corner will be the vector sum of the three wire fields:
B_net = 3B
B_net = 3(4π × 10⁻⁷ × 4 / d)
B_net = 3π x 10⁻⁷/d, T
(b) The magnitude of the magnetic field at the center of the square is calculated as;
each magnetic field in opposite direction will cancel out;
B(net) = 0
Learn more about magnetic field here: https://brainly.com/question/7802337
#SPJ4
A motorcycle is traveling at 25 m/s when the rider notices a traffic jam way ahead of them in the distance. Assuming the motorcyclist starts braking with an acceleration of -5 m/s^2 instantly upon noticing the traffic jam, how long (in seconds) does it take the rider to come to a complete stop? (Your answer should be in units of seconds, but just write the number part of your answer.)
The rider takes 5 seconds for the motorcyclist to come to a complete stop. The time it takes for the motorcyclist to come to a complete stop, we can use the kinematic equation that relates velocity, acceleration, and time:
v = u + at
v is the final velocity (0 m/s since the motorcyclist comes to a complete stop),
u is the initial velocity (25 m/s),
a is the acceleration (-5 m/s²),
t is the time we need to find.
t = (v - u) / a
Substituting the given values into the equation:
t = (0 - 25) / (-5)
Simplifying the expression:
t = 25 / 5
t = 5 seconds
Therefore, it takes the motorcyclist 5 seconds to come to a complete stop.
The time it takes for an object to come to a stop can be determined using the kinematic equation that relates velocity, acceleration, and time. In this case, the initial velocity of the motorcyclist is 25 m/s, and the acceleration is -5 m/s² (negative since it is deceleration or braking).
Learn more about acceleration here:
https://brainly.com/question/2303856
#SPJ11
Design topic Project: to design single-stage gear-reducer in Belt conveyor Working conditions: 1) The belt conveyor is expected to operate 16 hours per day with a design life of 10 years and 300 working day in a year. 2) Continuous one-way operation, stable load, The transmission efficiency of the belt conveyor is 96%. 3) Design parameter: 1.3kN 1.8kN Tractive force of conveyor belt(F/kN): Velocity of conveyor belt(v/(m/s)) : 1.5 m/s 1.3 m/s Diameter of conveyor belt's roller D/mm: 240mm 200mm C single-stage gear-reducer I
Power, rotational speed, transmission ratio Shaft of motor Power P/kW Torque T/(N mm) Speed n/(r/min) transmission ration i 9550XPI T₁ = n₁ N.m belt drive : ib Shaft of motor Output shaft gear-reducer: ig U Output shaft Input shaft JC Input shaft
The design project involves designing a single-stage gear reducer for a belt conveyor. The working conditions of the conveyor are specified, including the expected operating hours, design life, and transmission efficiency.
Design parameters such as tractive force, velocity of the conveyor belt, and diameter of the roller are provided. The goal is to determine the power, rotational speed, and transmission ratio for the gear reducer.
The design project focuses on designing a single-stage gear reducer for a belt conveyor. The conveyor is expected to operate for 16 hours per day, with a design life of 10 years and 300 working days in a year. The operating conditions involve continuous one-way operation with a stable load, and the transmission efficiency of the belt conveyor is given as 96%.To design the gear reducer, several design parameters are provided. These include the tractive force of the conveyor belt, which is specified as 1.3kN and 1.8kN, and the velocity of the conveyor belt, which is given as 1.5 m/s and 1.3 m/s. The diameter of the conveyor belt's roller is also provided as 240mm and 200mm.
The objective of the design project is to determine the power, rotational speed, and transmission ratio for the gear reducer. These parameters will depend on the specific requirements and characteristics of the belt conveyor system. By analyzing the design parameters, taking into account the operating conditions and desired performance, suitable gear sizes and configurations can be selected to meet the requirements of the belt conveyor.
In conclusion, the design project involves designing a single-stage gear reducer for a belt conveyor based on specified working conditions and design parameters. The goal is to determine the power, rotational speed, and transmission ratio for the gear reducer. By carefully considering the operating conditions, transmission efficiency, and design requirements, an optimal gear reducer configuration can be designed to ensure reliable and efficient operation of the belt conveyor system.
Learn more about conveyor belt's here:- brainly.com/question/3044640
#SPJ11
1. A sphere made of wood has a density of 0.830 g/cm³ and a radius of 8.00 cm. It falls through air of density 1.20 kg/m³ and has a drag coefficient of 0.500. What is its terminal speed (in m/s)?
2. From what height (in m) would the sphere have to be dropped to reach this speed if it fell without air resistance?
The height from which the sphere must be dropped without air resistance to reach a speed of 3.89 m/s is 0.755 m.
Density of sphere (ρs) = 0.830 g/cm³
Radius of sphere (r) = 8.00 cm
Air density (ρa) = 1.20 kg/m³
Drag coefficient (Cd) = 0.500
The terminal speed of a sphere is the constant speed that it attains when the force due to the air resistance becomes equal and opposite to the gravitational force acting on it.
So, the following formula can be used:
mg - (1/2)CdρAv² = 0
where,
m is the mass of the sphere.
g is the acceleration due to gravity.
ρ is the air density.
A is the area of the cross-section of the sphere facing the direction of motion.
v is the terminal speed of the sphere.
In order to calculate the terminal speed of the sphere, we need to calculate the mass and the cross-sectional area of the sphere. We can use the given density and radius to calculate the mass of the sphere as follows:
Volume of sphere = (4/3)πr³
Mass of sphere = Density x Volume= 0.830 g/cm³ x (4/3)π x (8.00 cm)³= 1432.0 g
The area of the cross-section of the sphere can be calculated as follows:
Area of circle = πr²
Area of sphere = 4 x Area of circle= 4πr²= 4π(8.00 cm)²= 804.25 cm²= 0.080425 m²
Substituting the given values in the above formula, we get:
mg - (1/2)CdρAv² = 0v = √[2mg/(CdρA)]
Substituting the values, we get:
v = √[2 x 0.001432 kg x 9.81 m/s² / (0.500 x 1.20 kg/m³ x 0.080425 m²)]
v = 3.89 m/s
Therefore, the terminal speed of the sphere is 3.89 m/s.
Now, let's calculate the height from which the sphere must be dropped to reach this speed without air resistance. We can use the following formula:
mgΔh = (1/2)mv²
where,
Δh is the height from which the sphere must be dropped without air resistance.
The mass of the sphere is given as 0.001432 kg.
We can use this to find the height as follows:
Δh = v²/(2g)
Δh = (3.89 m/s)² / (2 x 9.81 m/s²)
Δh = 0.755 m
Therefore, the height from which the sphere must be dropped without air resistance to reach a speed of 3.89 m/s is 0.755 m.
Learn more about density:
https://brainly.com/question/952755
#SPJ11
a) At what frequency would a 6.0 mH inductor and a 10 nF capacitor have the same reactance? (b) What would the reactance be? (©) Show that this frequency would be the nat- ural frequency of an oscillating circuit with the same L and C.
Answer:
The frequency at which the 6.0 mH inductor and 10 nF capacitor have the same reactance is approximately 20,462 Hz.
Reactance of an inductor (XL) is given by:
XL = 2πfL
Reactance of a capacitor (XC) is given by:
XC = 1 / (2πfC)
Where f is the frequency, L is the inductance, and C is the capacitance.
Setting XL equal to XC:
2πfL = 1 / (2πfC)
Simplifying the equation:
f = 1 / (2π√(LC))
L = 6.0 mH
= 6.0 x 10^(-3) H
C = 10 nF
= 10 x 10^(-9) F
Substituting the given values into the equation:
f = 1 / (2π√(6.0 x 10^(-3) H * 10 x 10^(-9) F))
Simplifying the expression:
f = 1 / (2π√(60 x 10^(-12) H·F))
f = 1 / (2π√(60 x 10^(-12) s^2 / C^2))
f = 1 / (2π x 7.75 x 10^(-6) s)
f ≈ 20,462 Hz
Therefore, the frequency at which the 6.0 mH inductor and 10 nF capacitor have the same reactance is approximately 20,462 Hz.
To show that this frequency is the natural frequency of an oscillating circuit with the same L and C, we can use the formula for the natural frequency of an LC circuit:
fn = 1 / (2π√(LC))
Substituting the given values into the formula:
fn = 1 / (2π√(6.0 x 10^(-3) H * 10 x 10^(-9) F))
fn = 1 / (2π√(60 x 10^(-12) H·F))
fn = 1 / (2π√(60 x 10^(-12) s^2 / C^2))
fn = 1 / (2π x 7.75 x 10^(-6) s)
fn ≈ 20,462 Hz
We can see that this frequency matches the frequency obtained earlier, confirming that it is the natural frequency of an oscillating circuit with the same L and C.
Learn more about capacitance, here
https://brainly.com/question/30529897
#SPJ11