18. Write conversion factors (as ratios) for the number of:
(a) yards in 1 meter
(b) liters in 1 liquid quart
(c) pounds in 1 kilogram
​

The charge on each ball is 6.1 ×10⁻⁸ C.

The definition of force in physics is: The push or pull on a massed object changes its velocity.

An external force is an agent that has the power to alter the resting or moving condition of a body. It has a direction and a magnitude. A spring balance can be used to calculate the Force. The Newton is the SI unit of force.  Force is a vector quantity and it has both magnitude and direction.

Let the balls have equal charge of q. Then, electrostatic force acting on each particle = √3 q²/r² dyne =  √3 q²/15² dyne =0.0076 q².

Weight of each ball = 13.3 ×980 dyne = 13034 dyne.

As the electrostatic force and the weight acts perpendicular to each other.

Hence, 0.1/√3 = 0.0076 q²/13034

q = 6.1 ×10⁻⁸ C

Hence, the charge on each ball is  6.1 ×10⁻⁸ C.

Learn more about force here:

https://brainly.com/question/13191643

#SPJ2

Answer:Air bags can leave you in even more injury, From the impact they give

You could end up with a broken nose,arm

concussion

Answer:

v = 9.04 m / s

Explanation:

For this exercise we can use the relation that the work of the non-conservative force (friction) is equal to the variation of the mechanical energy of the system.

          W = Em_f - Em₀         (1)

Starting point. Lower slope

        Em₀ = K = ½ m v²

highest point. Where is the skier at a height h

        Em_f = U = m g h

The work of rubbing

        W = -fr x

the negative sign is because the friction force opposes the movement.

Let's set a reference system where the x axis is parallel to the slope and the y axis is perpendicular

let's use trigonometry to break down the weight

        cos θ = W_y / W

        sin θ = Wₓ / W

        W_y = W cos θ

        Wₓ = W sin θ

Y axis

        N - Wₓ = 0

        N = mg sin  θ

X axis

         fr = m a

the friction force has the expression

         fr = μ N

         fr = μ mg sin θ

we look for the job

         W = - μ mg sin θ  x

where x is the distance along the slope

we substitute in 1

         -μ mg sin θ x = mg h - ½ m v²

let's use trigonometry to find the distance x

        tan 30 = h / x

        x = h / tan 30

we substitute

          -   [tex]\mu \ mg \ sin \theta \ \frac{h}{tan 30} \ x[/tex] = m gh - ½ m v²

we use  

          tan 30 = sin30 / cos30

          v² = 2g h + 2 μ g h cos 30

          v = [tex]\sqrt{ 2gh \ (1+ cos 30}[/tex]

let's calculate

          v = [tex]\sqrt{ 2 \ 9.8 \ 4 \ (1 + 0.05 \ cos \ 30)}[/tex]

          v = 9.04 m / s

Answer:

equipment for the measurement of microwave L bands with a range between 1 GHz and 2 GHz.

Explanation:

The electromagnetic spectrum can be calculated with the relationship between the speed of light, its wavelength and its frequency.

         c = λ f

For reasons of analysis and equipment used, it is artificially divided into ranges, with poorly defined limits and in some cases with overlaps between some.

For the case of analysis, f = 1.41 10⁹ Hz, we have the range called

* Microwave for f> 3 108 Hz to approximately f <3 1011 Hz

For the lower part of the frequency 3 10⁸ <f <3 10⁹ Hz we have UHF television channels and cell phones and military communications.

As the frequency observed by the researchers is in the UHF range, it is possible that they are using microwave equipment for communications, specifically equipment for the measurement of microwave L bands with a range between 1 GHz and 2 GHz.

Answer:

E =  1.64 x 10⁶ V/m

Explanation:

The electric field in the region between the plates can be given by the following formula:

[tex]E = \frac{\Delta V}{d}[/tex]

where,

E = Electric Field = ?

ΔV = Poetential Difference across the plates = 23 KV = 23000 V

d = distance between plates = 1.4 cm = 0.014 m

Therefore, using these values in the equation, we get:

[tex]E = \frac{23000\ V}{0.014\ m}[/tex]

E =  1.64 x 10⁶ V/m

Answer:

[tex]f = g \times \frac{m1 \times m2}{ {d}^{2} } [/tex]

[tex]f = 6.67 \times {10}^{ - 11} \times \frac{40 \times 40}{9} [/tex]

The answer is C I believe

Answer:

I would assume a force of gravitational pull.

Explanation:

Answer:  How powerful the pull is or how many magnetic things it can pick up at one time, or a heavy magnetic object.

Explanation:

Answer:

Drought

Explanation:

Answer:

the correct answer is C

Explanation:

For this exercise we can use the conservation of angular momentum, let's define a system formed by the disk and the other body, so that the torques during the collision have been internal and the moment is conserved.

Initial instant. Before placing the second body

          L₀ = I₁ w₁

Final moment. Right after placing the body

         L_f = (I₁ + I₂) w

the moment of inertia of the ring with respect to an axis passing through its center is tabulated

         I_{cm} = m r²

we use the parallel axes theorem to find the moment of inertia about an axis passing through one end

        I₁ = I_{cm} + m d²

where d is the distance from the center of mass to the new axis

        d = r / 2

we substitute

        I₁ = mr² + m (r/2)²

        I₁ = 5/4 m r²

The second body does not specify a specific shape, so we can assume it to be punctual

        I₂ = m’ (2r)²

        I₂ = 4 m’ r²

in the exercise indicate that

        m ’= m / 4

        I₂ = m r²

how the moment of inertia is conserved

        L₀ = L_f

        I₁ w₁ = (I₁ + I₂) w

        5/4 m r² w₁ = (5/4 m r² + m r²) w

        5/4 m r² w₁ =9/4 m r² w

        w = 5/9 w₁      

we calculate

         w = 5/9 12

         w = 6.67 rad / s

having the initial and final angular velocities we can find the kinetic energy of the hoop

         K₀ = ½ I₁ w₁²

         K_f = ½ (I₁) w2

the energy ratio is

        [tex]\frac{K_f}{K_o}[/tex] = [tex]\frac{w^2}{w_1^2}[/tex]

        \frac{K_f}{K_o} = (6.67 / 12)²

        \frac{K_f}{K_o} = 0.309

        [tex]\frac{K_f}{K_o} %[/tex] = 31%

the correct answer is C

Answer: I think its D

Explanation: Hope this was helpful...

Answer:

9v

Explanation:

Answer:

Distance = 13.9 meters

Explanation:

Given the following data;

Maximum speed = 150 km/hr to meters per seconds = 150 * 1000/3600 = 41.67 m/s

Decelerating speed = 3m/s

To find the distance travelled with this speed;

Distance = maximum speed/decelerating speed

Distance = 41.67/3

Distance = 13.9 meters

Therefore, the bus would travel a distance of 13.9 meters before stopping.

Answer:

making an observation

Explanation:

Answer: current I= 2 A

Explanation: when resistors are in series current I is same

Through each resistor. Potential drop along resistor R is

ΔV= IR. then I = ΔV/R = 6V/3Ω

Three resistors: R1 = 5 Ω,R2 = 3 Ω, and R3 = 4 Ω are connected in series to each other. A voltmeter connected in parallel to resistor R2 measures a voltage of 6 Volts, then the current flowing through the battery would be 2 Ampere.

Resistance is the obstruction of electrons in an electrically conducting material.

As given in the problem ,Three resistors: R1 = 5 Ω,R2 = 3 Ω, and R3 = 4 Ω are connected in series to each other. A voltmeter connected in parallel to resistor R2 measures a voltage of 6 V.

By using Ohm's Law,

V = IR

6 Volt = Electric current × 3 Ohms

Electric current = 6 volt / 3 Ohm's

                          = 2 Ampere

Thus, the current flowing through the battery would be 2 Ampere.

To learn more about resistance here, refer to the link;

brainly.com/question/14547003

#SPJ2

I learned the equation as P•V=k•T .

So x=1, y=1, and z= -1 .

Increasing the number of resistors in a parallel branch, decreases the total resistance of the system.

Parallel resistive circuit is one where the resistors are connected to the same two points (or nodes) and is identified by the fact that it has more than one current path connected to a common voltage source.

As more and more resistors are added in parallel to a circuit, the equivalent resistance of the circuit decreases and the total current of the circuit increases.

To learn more about Parallel circuit here

https://brainly.com/question/11409042

#SPJ2

Answer:

Volume of water displaced = 450 - 375 = 75 ml

Vr = volume of rock = 75 ml

Wr = 9.22 - 7.60 = 1.62 N  weight of 75 ml of rock

Density of rock = 1.62 N / 75 ml = .0216 N / ml

Density of water = 1000 g / 1000 ml = 9.8 N / 1000 ml = .0098 N / ml

Density of rock / density of water = .0216 / .0098 = 2.20

The specific gravity of the rock in the given water volume is 0.2.

The given parameters;

The specific gravity of the rock is calculated as follows;

[tex]S.G = \frac{weight \ in \ air}{Weight \ in \ water} \\\\S.G = \frac{450 - 375}{375} \\\\S.G = 0.2[/tex]

Thus, the specific gravity of the rock in the given water volume is 0.2.

Learn more here:https://brainly.com/question/19142897

three different states

Water is known to exist in three different states; as a solid, liquid or gas. Clouds, snow, and rain are all made of up of some form of water. A cloud is comprised of tiny water droplets and/or ice crystals, a snowflake is an aggregate of many ice crystals, and rain is just liquid water.

Answer:

Explanation:

Check out the Periodic Table attached here. The Carbon family is the vertical group starting with Carbon, Group 14. Nonmetals are in green, which element there is a nonmetal?

This problem involved half projectile.

initial velocity, vo = 20 m/s

time of flight, t = 7 s

(a) Simply use the formula to get the height, h:

h = vo*t - (1/2)gt^2

(b) To get the final vertical velocity or terminal velocity (vf), use the formula:

(vf)^2 - (vo)^2 = 2gh

(c) Use the formula find the horizontal distance traveled, R:

R = vo * cos(θ) * t

But since the angle involved with respect to horizontal is zero, and cos(0) = 1, we have

R = vo * t

Hope this helps~ `u`

Jai

Answer:

B

Explanation:

Because blocks 2 and 3 have sides with unequal forces while block 1 doesnt. Plz drop a follow if this helps! ❤

Answer:

The motion of an object is accelerated when its speed increases.

Answer:

option 5

Explanation:

because all u do is have to add them up

Answer:

D

Explanation:

because if the solvent is more than the solvent then we can't resolve it.

so our product will be suspended

Answer:

The answer is "892.90 N"

Explanation:

Following are the solution to these question:

Calculating the vertical force of the summation that is equal to zero:

[tex]\to TL \cos 65 + TR \cos 80 -520 = 0\\\\\to 0.4226\ TL + 0.1736\ TR = 520\\[/tex]

Calculating the sum of horizontal forces that is equal to zero:

[tex]\to TL\sin 65 - TR \sin 80 = 0 \\\\\to 0.9063TL - 0.9846TR = 0\\\\\to TL = (\frac{0.9846}{0.9063})\ TR \ \ = 1.0866\ TR\\\\\to 0.4226(1.0866) \ TR +0.1736\ TR =520 \ N\\\\\to 0.6328 \ TR = 520 \\\\\to TR = 821.74 \ N \\\\\to TL = 1.0866 \times 821.74 = 892.90\ N[/tex]

Answer:

0.116 N/m

Explanation:

Since the net force acting on the ring must be greater than 2.00 × 10⁻² N, and the surface tension T = F/L where F = net force = 2.00 × 10⁻² N and L = circumference of ring = 2πr where r = radius of ring = 2.75 cm = 2.75 × 10⁻² m.

So, T = F/L

= F/2πr

= 2.00 × 10⁻² N ÷ 2π(2.75 × 10⁻² m)

= 1/2.75π  N/m

= 1/8.64 N/m

= 0.116 N/m

Answer:

The recipe for a hurricane is a combination of warm, humid wind over tropical waters. The temperature of tropical waters must be at least 80 degrees F for up to 165 feet below the ocean’s surface. As this warm water meets the wind that blows west from Africa across the ocean, it causes the water to vaporize. The water vapor then rises into the atmosphere, where it cools and liquefies.

Explanation:

I hope this helps

Answer:

Matthias Schleidan

Explanation:

because Matthias Schleiden found that all plants are composed of cells, and communicated the finding to Schwann, who had found similar structures in the cells. Other researchers confirmed the similarity, as explained in his book, where he concluded, "All living things are composed of cells and cell products.

This became the cell theory.

I learn that in my old school.